Viewing all customer Discussions for:

S385-30 30" Series 385 Channel Balance

Stamp in channel "29 3" then sideways it says BS1 or 8SI ?

I need to replace my window channel balance. It measures 30" metal-to-metal. There's and engraved stamp of 2920 as noted in the photos. Please advised.

Hello can you tell me what window balance to order?

Hello, needed to order new window balances for most of my windows. Want to make sure I'm ordering the correct size. Thank you.

Mine is a vertical push up window. On the fallen balance it writes 29-6 KX CMC 7 which i am not quite sure if that's helpful. And my window brand is Milgard

Hello, I have a non tilt window that needs new replacement Channel balances. The channel balance that came out of the window sides are inscribed with '29 3 FX CMC 11'. Can you advise the best Swisco match for this channel balance along with top and bottom stops that get screwed into the window frame ... (cont.)

Looking to replace 10 years old channel block & tackle window balance 29ds 48l on no tilt high impact windows. What will be the best option? Thank you

I have a single hung Lawson impact window that I need 2 new balancers for, the number on balancer is 29DS48L. The metal part measures 30", the total length is 31" including plastic ends. Non tilt Metal length 29-7/8 Width 1/2"

Hi I need the correct replacement 1/2'' balance sash. I also need to top sash clip guides for the window. Please send correct part numbers when you can.

It's 30" long (metal only), 1/2" or 9/16" wide channel, bottom shoe 1 1/16" deep, wings on top and bottom shoes, stamped "29 9 CX CMC 4" It closely resembles the 385 series. I also have a second balance to replace, pictures attached. It has the same style and dimensions except it is stamped 29-4 JX ... (cont.)

Hello, The channel metal to metal is 30" Please let me know what is swisco part number to order? Thank you Mike

Hey! I need help finding the right window balance. I know that they are 29-4 (so I know I am looking for 29 inch balances) but I am unsure of the weight. I found block and channel balances on your site have the same clips as mine, but still unsure of the wight and how to figure that out. Both sets o ... (cont.)

Can you please help me identify the right window balance to order? Please see attached photos. The length is 30-inches length and 5/8 inches wide but unfortunately when I was removing it, the parts fell out due to the poor condition. Weight of the window is approximately 30 pounds. ... (cont.)

I need to replace 4 window balancers. There are no markings on any of them. The length of the metal part of the balancer is 30". I have attached 3 pics of the balancer and one pic of the sticker on the top edge of the window. Please let me know what I need to buy and how much those would cost th ... (cont.)

Nuair double glazed window won't stay up, looks like bad balances. Measurements 29-7/8" long, 1/2" wide, 5/8" deep

Good day! I am looking for a 30" channel with matching sash (take out) clips. The channel top and bottom (shoe) must be winged. My current channel isn't stamped, so I need to weigh the sash to determine strength. Thanks for your help!

I need help ordering two replacement balances for this one window. The number I see on here is 2930. Please let me know which balance to order. Thank you.

Hello, Looking for the right Milgard balancer replacement. The stamp of the current balancer is "29 4 lv cmc 2". I've attached several photos. Thanks in advance!

Need a replacement. Cws window. Balance 30 inches long with markings 29. 4AA BSI. The window weighs 24.5 pounds Thank you!

Please identify the correct 300 series balance with these included pictures. Thank you