Viewing all customer Discussions for:

S385-33 33" Series 385 Channel Balance

I'm needing to find a matching channel balance replacement. Can you help me find the right part to order? The metal part of the channel is 33 inches long and I measured the depth of the plastic part that protrudes from the back as just over an inch at around 1.08 inches.

Amsco window channel balance with a broken cord. Channel balance is 33". Thank You.

Hello, I have 5 windows (15+ old) that won't stay up when opened. One window the channel balance part fell out so I was able to capture the attached photos. The part is 33". I pray you can help. Thank you Anna

Need to replace 4 ea balance. Please advise.Thank youGreg

I'm trying to identify my Milgard window springs. House was built in 2004. The length of the metal part of the spring is 33 inches. Can you help identify a replacement? I have attached photos.Thank you,Rod

we need 2 different balancers 1. code 3230, 33" - 40 pcs 2. code 2820, 29" - 120 pcs not sure about what type of shoe and top attached

Hi, to replace window balancer. It has "32 4 HQ CALDWELL" printed on the side. Could you please show me which part should i pick? Thanks. Warren

Trying to order the correct balances.

I am in need of some Milgard channel balances.One is numbered 20 3 DV CMC7 x2And One is numbered 32 5 GV CMC2 x6 I appreciate any assistance in getting these replacements. Thank you ,Tony

Window is marked P.G.T.window weights 31 lbs. Please let me know if any other photos are needed.thank you chris

Hello! I am looking for assistance on identifying the channel balances. Attached are photos. The overall length is 33". The width of the balance shoe is 1 1/8" The identification is different between the two. Not sure why. One side is 32 4 ER Caldwell. The other side is 32 9 KQ Caldwell. Thank y ... (cont.)

new part

Hello, Can you please direct me to the correct part number for my Milgard window balancer. I will need 2. Numbers on the balancer is 32 4 DV CMC 7 Thank you.

I am looking for 2 complete channel balances for my non-tilt Millguard window. The sliding window weighs between 25-30 lbs. I have included pictures of the channel balance I removed from the window. I question if it was the right balance to begin with as it may have been replaced before. I measured ... (cont.)

Hello, I have this window spring and the end looks slightly different than what is shown on your website. I'm know you can direct me to the correct part to purchase. Thank you, Kyle

My window balances have the markings caldwell 32 4 FQ. I need 10 which balances do I needs I also have a 26 4 AQ as well. Thank you

Replacing the balances in single hung vinyl windows. original part is 33 inches long (not including plastic end pieces), 9/16 inch wide, and 5/8 inch deep. Stamped markings on part are 3230 BSI.

I have Milgard windows. I have 2 window channel balances that are broken. One is 33 inches long and stamped 32-4. It is 5/8 depth and 1/2 inch width. It has winged upper and lower parts. The other one is marked 26-5. It is 5/8 depth and 1/2 wide. It has a lower winged and I suspect upper winge ... (cont.)

Attached are photo of the parts that we need: Qty (4) 3250 balancers (metal length is 32 7/8" width is 5/8" Qty (4) 2640 balancers (metal length is 26 7/8" width is 5/8" Qty (10) sash shoes Qty (2) steel clips used to hold the balancers in place during installation. Please let us if ... (cont.)

Hello, just looking to make sure we order the correct replacement parts. Thank you