Viewing all customer Discussions for:

81-272 1-1/2" dia Roller And Axle Kit

Hi I have a double sliding glass door.It is a KC series 7000.I am looking for some replacement roller parts. From center of bolt hole to center is 6&7/8 inch. Outside dimension of roller looks like 1&5/8 inches. Looks like 7/8 inch wide. 5&3/4 long It is stainless steel with nylon rollers. Thanks Bo ... (cont.)

The rollers for our sliding glass door need to be replaced, but I have no idea how or if it can be done. There are no identification marks on the door itself and the rollers are attached to a single , track-like assembly that screws directly into the bottom of the door as one unit. Any help identi ... (cont.)

We purchased the door from Lowe's and I believe it is a Reliabilt. One wheel has collapsed because its bearing has broken. The case measures 4.5" x 1 5/8". There are two screw holes on the top of the case. I apologise that I did not photograph the door with the roller assembly installed but I ... (cont.)

Need parts that can replace this roller. I don't see anything like this on your website. Maybe it's discontinued? Is there a part that I can use as an alternative? This is a Monarch mirror door with brass frame.

Trying to identify and find rollers and lock mechanisms parts for old slider in my rental. Thanks, Eric

Do you offer a solution for this roller? If not is there another that could be used for the project?

Door is from 1963. No identifying name. Wheel dia. 1.5" assembly overall width .760" no counting detents. Overall height 1.44" overall lenght 4.125. Please call me with any questions 808 896 3911. Need four assemblies or just wheels if you don't have tha assembly. Wheels are 1.5" o.d. .350 wide. The ... (cont.)

I looking for replacement rollers and possibly the housing as well for the attached images. The house was built in the 57 and I think the sliding glass door / sunroom was added early to mid 60's. The frame is entirely aluminum . There are 2 rollers on each door panel . Each door is 48" x 81" approx. ... (cont.)

Hello, I don't see any markings are numbers on the door itself but this is the wheel that I took off

Hi, My name is Luis. I would like to know if you carry the part of the pictures I uploaded. I believe my sister needs five. Thank you for your attention in this matter. Luis

Looking for a pair of roller assemblies for an very old sliding glass door. I have searched far a wide and can not see anything like this. Any help would be appreciated.

I recently replaced both 81-112 door rollers and the 6' door track. I have adjusted the height up and down many times but the door is very slow and sticky. I have also used your recommended slide lube. Please help. Any suggestions?.

Hi there. My mid-50s slider is suffering and in need of new wheels. I've searched the internet for photos of the same wheels, but no luck. The one identifying name is on the inside, but it's missing some letters so I'm not sure what the word actually is. The height adjustment on this door has to ... (cont.)

Roller assembly is 2 3/4" long & 3/4" wide Roller wheel is 1 1/2" in diameter Pin is 1/4" I haven't seen any rollers that even look like this !! Are there maybe updated or superseded replacement rollers available?? Thanks ?

2.75 x 11/16 wide x 1.375 H frame w/ 1.5" diameter wheel OA height 1.75 No adjustments. Screws in from bottom with two #8 screws, 2.25" on center.

No markings identifying manufacturer. Sent picture of door locking mechanism to assist id. Steel wheel appers to be about 1 1/2 inches. The roller has two screws one on top 3/8 from end to attach to frame and one on the end about 7/8 inches from the bottom to attach to the exterior of the frame at t ... (cont.)

Looking for replacement Roller for Aluminum patio doors. Attached are pictures. I believe the roller bearings are worn out. Others two doors roll like butter. I welcome and await your expert advice.

Rollers are 1 1/2" diameter with an eccentric roller axle that allows for door adjustment. There are 2 rollers on bottom and top. The bottom of the door is 5/8" wide and 1 7/16" deep. Please advise on repair and parts needed. I do not see any replacement on web site but open to suggestions. These ar ... (cont.)

It's for a aluminum framed 79-1/2 x 49 slidingpatio door,no markings or numbers I could find. Installation date of the original patio doors is believed to be 1963

I'll be happy to add more pictures on request.