Viewing all customer Discussions for:

26-089 Pivot Bar, 3"

I need 4 of these Mastic window pivot arms. It?s about 3 inches long (longer is ok). Can you please help me. Thanks.

Thanks for writing in. I'm afraid I can't narrow down what you need from that information alone. Window hardware is typically generic even among brands. We will need to see both the pivot bar and pivot shoe removed from the window. The width and thickness of the pivot shoe would be helpful. For the ... (cont.)

These are the pins that are shaped like little CThese are the pins that are removable from the bottom the window that ride in the window cams that hang from the balances

Good day there are two brass brackets that hold the bottom of the windows into the equalizer cylinders on the side of the windows I need those brackets as shown in the picture and the model of the window number is also shown in the picture. Can you help

Need replacement coil spring balance pivots for Accent Windows installed in mid 1980s in Denver, Colorado. Double hung vinyl windows total width about 35 inches and total height about 51 inches. Front and back edges of the plastic case measure 3-11/16" not including the 2 tabs on top. The thickness ... (cont.)

Would like to order these parts tilt latches (lh 26-177 & th 26-176) also pivot bars 26-089 & locks CW16T125 2.

The four pictures show the pivot bar which inserts into the housing shown. The housing sits in the frame of the window and the bar fits into it on one end and the plastic shoe on the other end which is attached to the balance. It is the little bar which I am missing. To me it looks like 26-089 exce ... (cont.)

Hello....I need a sash pivot bar that I can not find on your site. It is 2 1/2" long with one hole 1 1/2" from the end. It is 5/16" wide and 3/16" thick. The metal is shaped like a "U". Do you have something like this? Thanks!

Looking to replace our pivit bars as they have broke. No numbers or name on them

All are 27". Is there a difference between the blue and red tip ?Also need some window channel locks. Photo to come.

Hello,I need to replace a bent pivot bar for the bottom sash of a double-hung window, please. I have looked online at the Swisco parts inventory and cannot find a suitable replacement. Attached is an image with written dimensions for a healthy pivot bar that is not broken or bent.Also, as seen in on ... (cont.)

I finally opened one of the windows and it seems that the pivot bar is missing on one side....

I need to replace both sash bars on a window in house we just purchased. They have number 6221 stamped on them. Attached is photo. Please note part of left side shown in picture broke off and is missing. Also there is channel on right side of bar that fits into channel along both sides of window. Pl ... (cont.)

Sir, I am looking for a 4 inch long (or longer) pivot bar similar to your model 26-040 which is 3 inches long. I am looking for a longer bar because the receptor grove on the window is in part missing. See the attached photos: 1900- existing pivot bar at left side of window - 3 inches long 1897- rig ... (cont.)

I'm liking for a window balance or spring replacement. I have attached a picture of the lake indentifying the vinal 2 pane window as a Series 710 from "MFR: PHP-62". Do you have a replacement part for this window? Thank you.

Good Morning Swisco, Thank you for being out there providing these parts. I am a contractor and have to replace 6 coil balances. This is my first time in doing so. Here are the only pictures I have from the job ...I am sure you will need more. Here is the info on the window stamp, this ... (cont.)

Here dimensions for this old shoe depth .5 inch height 1 inch width 1- 1/4

Pivot bar cross section: 5/16" x 3/16" Length: 3" to 3 3/16" Required holes, measured from square end of bar: 1 13/32", 1 7/8" and 2 5/8" These are the 1st, 2nd and 5th holes from left to right in the attached photo. The 3rd and 4th holes are NOT used. No names, numbers or markings on existing pin. ... (cont.)

Looked everywhere, just need the inside part that slides into the housing, about 3 in long and 1/4 in wide. As long as it will Work and be an inexpensive fix.

Attn. Tom. This is the pivot bar in the attachment. Help an old man out.