Viewing all customer Discussions for:

S395-24 24" Series 395 Channel Balance

I'm looking for the correct balance replacement for my windows. The metal portion is 24in and the marking on it is "23 3" along with what looks like "BS1"

I'll need 20 pieces. Tks

Hello, i need help with part order. The length of metal is 24 inches and the number stamped is 2340. I need 4 pieces

I am looking to replace the channel balance on 8 PGT SH 4000 windows. Photos attached. The balance is 24" long (metal only). I also need the part for the top of the window (photo attached), and the clips that release the window for removal. The stamp on one balance said 23-2 DS Caldwell (photo ... (cont.)

Need window balances Stamp says Caldwell 23 9 34# 19 LT JQ They are 24 inches long not including the plastic peices

Need help in identifying these balances the window is 26 1/4 tall the width is 46 3/4 I also have windows 34 1/2 "wide windows x 261/4" tall two of them that I need balances for also

I don't know where the post is but I'm trying to replace some bad window glides. channel is 24 inches long, The stamps on it are 2320 KC BSI or RSI

I need to replace my channel balance for my PGT single hung window. The aluminum channel is 23 1/2" long x 1/2" x 1/2" and marked with 23-2 JX CMC 11 What replacement part do I need?

Please identify a replacement for 2 of the Balances shown in the attached photos. The metal portion is 24" long. The window sash weights 24 1/2 Lbs. I will place an order along with some other parts I identified. Thanks and Regards, Dave Fisher

Metal channel is 24 inches long Stamp says 23-3 02 13 VBS Window is very hard to open, feels heavy. Spring and cord on channel balance are not broken/impaired. Do you recommend replacing? (Kitchen window over sink)

Says 2330 and is 24" metal case end to end

Length 24"Markings: the number 2390 is stamped in a horizontal position, then the letters FG (horizontal) then the letters BSI in a vertical direction; then the number 34 afterward in a horizontal position. No other markings that I can find.Need help identifying so I can place an order.Thank you.Ken ... (cont.)

I need 2 sets of balances for PGT windows. 1 set is marked 23-2 IV CMC 7 and the other set is marked 29-5 IV CMC 2. The top ends are winged and the bottom are not winged. Please see included photo. Please advise if you have these and what my cost would be. Thank you.Regards,Tim

I have the weight of the windows and all pertinent info. Please call me so I can place the orders

I have a balancer that looks similar to the 24" SERIES 395 and has a stamp that says 2323DSL (with a little "RB"). What sash weight range should I get? I will be buying 2 new ones.

Hello, can you identify the top and bottom part. This is a 24 inch long, 1/2 inch wide B.S.I. # 2320DG. What is the proper replacement part from Swisco? Thanks.

These windows were installed in 2001.

Caldwell Block and Tackle Channel Balance for PGT Window (non-tilt 52W x 75L)24 inch (metal to metal)30 lb sash weight5/8 inch width (1/2 inch channel)TOP CAP:Winged (15/16 inch wing to wing)9/16 inch width1 1/4 inch (1 and 1/4 inch) lengthBOTTOM foot:@1 1/2 inch length (poly to poly)9/16 inch width ... (cont.)

No other markings than 2340

This came from a PGT single hung window that has tempered glass in it, along side of a door very heavy. Would like to get 2 of them. If you can help me out with this issue I would very much appreciate it. Thanks Ed