Viewing all customer Discussions for:

S395-24 24" Series 395 Channel Balance

I need replacement balances for my pgt windows. label states sh 400, aluminum, insulated glass, single hung, size is a 3-4.on the balance it is stamped 23DS 30can you help me? Scottmetal is 24" long and 1/2" w

Can you send us pictures of the top and bottom fittings on the balance to confirm what you have?

The rope on my window balance broke and so the window only hangs on one balance that has the rope intact. I took pictures of the balance and a picture of the sticker I found on the inside of the window. Could you help me figure out what I can replace this with? These are Atrium windows and the metal ... (cont.)

String broken on balance. markings are 2340 HE BSI The HE is very small just after the 2340. The BSI is sideways and very small just after the HE. The markings are faint and would not show up with my camera.

i am looking to replace my single, hung, non tilt window. the length of the channel, without top and bottom fittings is 24". the only markings on the channel [printed and not 'stamped'] are "23 4 GS Caldwell'. could you please direct me as to the correct parts to order/ many thanks. paul ... (cont.)

Attempting to identify the correct Channel Balance and Top sash guides. Require 2 24 inch Channel Balance Springs and 2 Top sash guides. Pictures attached.

stamped 23 4 24" l0ng 1/2" wide can you tell me what part # this is? I need to replace 4 of them for 2 windows

I need to replace 6 channel balances on my PGT windows. The replacement part must include the top, shoe, spring and cord as shown in the photos. The PGT part number for each channel balance is as follows: 23-9 HV Qty=2 29-4 JV Qty=4

Hello, I have a 24" channel balance (yes, 24" not 23") for a Viking window marked 2320 EG that I'd like to replace. Took some photos but the Add Photos button isn't responding. Can you help pin down the replacement part I need?Thanks,Will

Do you have a replacement? See Photos

I?m a contractor but is trying to identify the proper replacement balances for two different PGT single hung windows. I?ve attached some pictures with the imprinted part numbers and some

I'm including pictures of what I believe to be similar to your 24" SERIES 395 CHANNEL BALANCE. I've removed a few of the plastic end pieces, and tried to get a few angles to compare to yours. I would just like to make sure I'm getting the correct parts before I order them. In particular, your PGT To ... (cont.)

The length from the bottom of clip in window frame to bottom usable hole is 22" Picture 2076 has 2340 BS1 or BSL on it. The channel top is 1/2" across. I need to order two of these balance channels.

Here are photos of the bad balancer. The width is 0.5" and the length is 24". Can you please help me find a suitable replacement?

Hi, I need a few replacement channel balances. As I could identify from your website what I need is the Series 395 balances. I need some 24"long and 12"long. But I can't find the 12" sizes on your site, all are 13" and longer. I include some pictures of the 12" balances. The 24"balances have the sa ... (cont.)

Please help me identify what replacement parts I need for my window. I believe some of the plastic pieces have broken or been worn down. The right side track does not stay in position any longer. If I push up on the track piece on the right side as I am raising the window it will stay contained. ... (cont.)

I would like to purchase two sets of window channel balances but I can not locate the correct one. I measured 1/2 inch track that is 25 inches long. I added pictures of the top and bottom clips I forgot to add this is for a non-tilt window. I think the part I need is the Series 380 with the ... (cont.)

Says balance 24

I am need if assistance in determining the appropriate window balance for this Viking Window. There are no balances present currently. The bottom (sliding) section of the window is 26 1'/8" H x 15 3/8" W. The depth of the window is about 1" and the channel is just under 3/4". Thanks for your a ... (cont.)

I have a non tilt,sliding, double pane window. The sliding part is 30x45. The balance is 28 inches long. I've attached photos of the markings and the top and bottom ends. I need to know which of your models I need. I appreciate your help. Thanks, Jim