Viewing all customer Discussions for:

S395-28 28" Series 395 Channel Balance

Hi, I need to find replacement part for my window sash balance and tackle. The metal measures 28 inches in length by 5/8 inch in width and 5/8 inch in depth. It is stamped w/ B.S.I. 2740. I need to replace these on a few windows and was hoping you could help me find suitable replacements. ... (cont.)

Hello, it looks like I ordered the wrong part. I ordered the S350-28, but it does not have the flanges on the opposite tip compared to the old one in the photo. I assume that is why the handyman could not get the guide to stay in place. The closest part that I see is the S380, but it has flanges on ... (cont.)

Which parts to order?

Hello, Recently bought a house and found most of my windows do not open or will not close after opening. Took these off and am hoping to get replacement parts asap. There's a stamp number included on the photo that led me to a caldwell non-tilt block and tackle balance but I am unable to choose the ... (cont.)

I believe this is a "28" Series 395 Channel Balance (Product Code: S395-28; Option: 2740)" per the attached images. I only pulled one side (the broken one), but am planning on replacing both (and then have a well used spare). This balance appeared to have lost the window frame clip as I couldn't ... (cont.)

Dear Sir or Madam,Reading the previous posts from Austin Texas, it looks like I also need part S395-28 with the 2740 option. Can you please tell me if this is correct? Also, is the the correct link to this product: https://www.swisco.com/28-Series-395/pd/Series-395-Channel-Balances/S395-28Thank you, ... (cont.)

1540 @ 16" 2730 @ 28" 140" of the spine or whatever it is called.

Alenco 2730 Window Balance is old/bad. The balance appears to be 1/2 inch and 5/8 inch?

Length is 28in on the metal frame, end to end. Unit is stamped "2740 HA-BSI" and came original on home built in 1996 or so. Looks to be model S395-28 for $10.45/ea.Please see images. Thank you very much.Barry

Hi I need a few these 28 inch 2740 channel balance for my windows, can you tell me the model number?

Hi, I am looking for a pair of channel balances, my old ones are marked 27 3 CR CALDWELL and the metal channel itself (not including plastic ends) measures 28 inches long, 5/8 deep. Please see attached three photos. The window the channels move up and down weighs ten pounds. Could you please help me ... (cont.)

b2740 and b2730 I couldn't find a top and shoe that matched what I have.

I'm looking for replacement channel balances (S395?). Original parts are stamped 2790, but I'm not finding them on your site. Are they available?

Dear Sir/Madam,I am looking for a replacement channel balance.The markings are 27-4 and I have included pictures of the end pieces.Sincerely,Chris

The first is a 27-3 AK5 CMC 50 (non tilt windows) the metal is 28" in length The bottom are both pinned in place plastic piece is just a fraction that I measure over and inch. The second is an 27-4 G15 CMC 50 (non tilt windows) the metal is 28" in length. Attached are pic's for both, let me know ... (cont.)

Need to buy 10 window balancers. Metal portion is 20 inches and is inscribed with "2790 JM 31."

Hello. Please see photos to help me identify the replacement channels that I need. The metal channels are 28" long and 1/2" wide

Hi. I need repair parts for an ADAMCO window. The channel is 28" long, 5/8" tall on the side, and 9/16" on the narrow side. It's a single-hung window. Pictures are attached. The number stamped on the channel is: a 2740. I need to know if the plastic parts, spring, block and tackle, etc. are in ... (cont.)

The metal part of the Channel is 28in long, 1/2in wide. #2720 is stamped on Channel. I think your S395 Channel is the one I need. What do you think? Regards, Brent

Hello, Swisco team. We have a window that has a cannel balance 2730 BSI and another one 2740 BSI. The length of them is 28" without the inserts.