Viewing all customer Discussions for:

26-297 Pivot Bar, 2 1/4"

Some of these pins are rusted into place.

I have no brand name on the window. It just says care free. The pictures are from another identical window. Any help is appreciated.

The tube is 1/2 inches and space between the studs is the same

Pivot pins made of channel iron that tapers from 5/16" to 1/4" Wide, they are 3/16 high, and 2 1/4" long and the tapered end (1/4" wide part) is 1/2" of the 2 1/4" length. There are 3 holes for screws at 15/32, 1 3/16, and 1 1/2 from the 5/16 end of the 2 1/4" length.

I need two different window pivot shoes like the ones in the attached photos. Do you have anything we could use?

I have carefree windows from 1999. It appears my pivot stops have failed, prolly due to operator error. I can't get the spirals to stay attached to the pivot block. Are there replacement blocks I can get.

The window assist are broken, the lead keepers are busted out of holders that help lift window. One picture shows the lead keeper holding the rods which are connected to slide. Hoping you can help me out, thank you Don

mobile home windows. these were all rusted out. when you raise the window. window could fall out. want stay raised.need to replace in every window. will need 2 for each window. time frame to order.

Good Afternoon,We have 4 CareFree windows which have broken bottom where the pivot plate attaches. The window are unable to open. Is there a replacement bottom for the windows or an alternative repair?Thank you in advance for your response.Roberta

Spiral Balance -Green Pivot Bar - 2"x 7/8" wide x 3/8"Thick Pivot Shoe- 2 1/4" PN26-297

Hi guys, Well I ordered the 900 series balance system and pivot shoes Product Code: 15-134 swico. The problem now is, everything fits , except the cam hole, it's to small, the pivot bar is a little bit bigger so it won't fit in. So what are my options? New pivot bars? Or new pivot shoes?Best regards ... (cont.)

I think this is a pivot bar

one photo of screen needing replacement; do you sell screens. two photos of bottom of window of apparent plastic weather strip held in place by screws--do you sell these?

Hello, I am looking for the pivot bars to match this one. Also, the vinyl where these attach is cracked on most of the windows, so the bars will wiggle when going up and will most likely break soon. If there is a longer bar that has a hole that will match the 3rd hole, or just further back where I c ... (cont.)

Pin that is in the bottom of the window sash, that clips into the end of a spiral balance. Held in place with 2 sheet metal screws. About 2-1/4 inch long.

I need 2 of these. They connect to the bottom of the sash with 2 Phillips screws and the end fits into the spiral channel clip to allow the window to go up and down in a controlled fashion instead of just dropping.

I'm trying to repair windows in a 1970's model mobile home. They had pivot shoes shown in the attached photos... I couldn't find a good match so I went with the 15-179 which matches length, width and depth but requires a round end on the sash pivot bar (it seems to me) to fit into them, the one on t ... (cont.)

I ordered pivot bar 2 1'4" 26-297, but I forgot to order screws for it. So I looked at your website for the screw that goes with it. I saw the Phillips pan 8-32 x 3'8" self-tapping ss machine screw 33-096. It looks like it has a chunk cut out of the end of it. Is it supposed to look like that? Is it ... (cont.)

Spiral Balance is round with white cover and is 28" long, 3/8" wide and has red tip Pivot shoe is 2" long, 1' wide and 1/2" deep. Will replace mechanism on both sides, just need something that works. Stationary top sash ans pivoting bottom sash.

these are 3/8 pivot shoes. They are 2"x 1". The window is 20 years old and i didn't see anything on the website that matched. Will anything else work?