Viewing all customer Discussions for:

26-297 Pivot Bar, 2 1/4"

Hi. I've attached pics of bottom of window with missing pivot bar pins. I also think the housing area for the pins is missing (but not sure). I believe the pivot bar was 26-297. Based on pics is there another bar that would work?

I took my current balances off and they are on tilt in Windows. The size of balance is 3/8 width and 27" long. The current color is green but on your site there is only a red and White option. Which do I get?Also any advice getting out pivot pins that rusted so bad the crumbled and snapped off? ... (cont.)

Located on the bottom left and right of the lower sash, this pin slide into the shoe connected to the balance rod. Looking at the end of the pin, it is shaped like a "U" with sharper corners. The vertical sides of the "U" are 3/16" and the base of the "U" is 5/16". The entire pin is 2 1/4" in len ... (cont.)

Hi, I talked with gentleman last week and told me to take pictures and send them in.The metal spiral balance is 30"The plastic tube is 29" x 9/16"DIAMENTER.The track with holds the metal spiral connected to the bottom piece is 1 3/8"My Name is DaveI need pieces to fix my window. Thanks for your help ... (cont.)

Hello,Unfortunately there is no markings on the windows. The accompanying pictures should give you the size and hole spacing. They appear to be worn on the ends which would figure as serveral have completely rotted off. Please let me know if you have this and the cost per unit as i will need about a ... (cont.)

I am in the need of a ribbed balance rod 2 single hole cam pivot bars a short clip on the balance and a pivot shoe like the ones in the attached pictures thank you mike young

These are for CareFree brand windows. The tip is red, the length is 29 inches, and the diameter is 3/8 inch. It has "ET A" on the side of the tube.

I'm working to replace the spiral tilt balance, pivot shoe and pivot bar in windows that were used in new construction in 1997. The pic I've included is the bottom corner of the window. Do you have a pivot bar that would be compatible with this? The pivot bar I found on your site seems like it wo ... (cont.)

I need a few pivot pins to fit a CFA window group vinyl window in our Shultz mobile home (made 1997). Pins are rusted off on a few windows. My pivot bar is 2.25" long, not 2.5 in your catalog. it is 1/4" wide on the working end; 5/16 on the back end (that slides into the window). the thickness is c ... (cont.)

My townhouse built in 1996. There are 13 Carefree vinyl windows with single huge, size 36"x60". Shoe thickness is 3/8". The balance bar is 3/8" x29". Each sash weight is 18LbMy problem is 6 Pivot bars are missed and only left holes in frame. Two contractors said they cannot repair them. I try to fix ... (cont.)

The tilt pivot bars on my windows are 2" long. 1/4" wide, 3/16" tall. The single screw hole is 7/16" from the inside end. Help me please. Thank you! Blessings

HelloI am looking to purchase about 100 pivot shoes as shown in the pdf file and pics included.Please let me know if you can locate and sell.ThanksBizhan Aref

Please look at the image attached

The balance is round in form and measures total length of 30 1/2 inches and about 7/16 inch wide. The part that goes in the channel is 1 inch wide and 2 inches in length. The piece that releases the window on top of the sash is 2 3/4 inches in length and 1 inch wide. The metal pieces at the bottom i ... (cont.)

The "stopper" for many of my windows has had the screws that hold it in place rusted out. This is the part which locks the window in place as it slides up and down. Not sure how/where to replace this.

Have a few single hung windows need part window rotates on and the rail that connects into clip

I have a spiral balance that has a white plastic housing that measures 28 inches in length and 3/8inches round. The spiral completely extended adds another 28 inches to the length. The pictures or the mechanism in the channel of the window has no way of coming out at this point. So if you have the s ... (cont.)

This part stays in window sash on a tilt window it is missing the metal prongs that hold the block tied to the string on a ribbed channel balance

The label is showing the window type, and the pic of the plastic insert that attaches to the spring is the part that we need. It's plastic, but metal would be okay also. Please advise if you have this part. The dimensions 14/16ths wide by 1 15/16ths high by 7/16ths deep. Thanks again. LindaThanks! ... (cont.)

Hi I have owned a double wide for 22 years that have carefree windows need a few balances. How do I go about ordering right ones. What do I need to measure? Also have a few broken shoes. So that also what do I measure?