Viewing all customer Discussions for:

15-195B 1-1/4" T-Lock Balance Shoe, Open Cam

Looking to make sure I'm ordering the correct balance before I order them. Metal channel measures is 26" long and 9/16" wide. It is stamped with a 26C BS and looks like is probably your S795-26, but mine has a hook clip on top, where the one in you photo is a screw in clip. Thanks for your help. ... (cont.)

I'm seeking for the balance and shoe in the image that i provided in the attachment. I would also need to know if I need a custom balance or not?

Looking to identify the Channel Balance, it is stamped 27C and uses the pivot type in picture. Thanks

I just want to give you all information that you need to correctly identify what I need. Here are photos requested which should better show information. Need 2 each S795 series and stamping is 28D which is for 23-28 pounds sash weight. Need hook end balance clip attachment 15-198. You mentioned t ... (cont.)

I need to replace the pivot locks on my windows. Attached are pictures. They measure 2 inches tall 1 1/4 inches wide and 1/2 inch deep. There are PAT# D467490 on the top of the pivot lock and #4810108 on the bottom of the pivot lock. Any help would be appreciated.

I need to replace the channel balances is two tilt-out windows. Windows are the same size and manufacturer, and were installed in new construction in 2004. I've viewed your videos and looked at the available balances. My balances appear to be plain channel, 30"; stamp 30B; standard bottom and two ... (cont.)

Need part number for this channel balance. 26-5, RV, and BSIN are stamped on the side.

I have 4 of these broken on some Silverline by Andersen windows in my home. The sash balances are stamped: 26-5 and TH and BSIN. Can you make a recommendation for replacement parts I can order from you?Thank you, Leo

Can you help confirm this part type I need? Thank you!

Hi, Need T-Lock Balance Shoe replacement part# for PlyGem 1500 series vinyl window. Thanks Steve

Need to match these up please

Have a house full of American Craftsman new construction double hung tilting vinyl windows. Majority of the windows are 3/0x5/2. Purchased around 2007 timeframe. Need to verify replacement parts needed. Top sash has a 23" balance and bottom sash has 25" balance, which I believe to be your Series 795 ... (cont.)

Hello, I have determined that my channel length is 33" so I would need part S795-33 with part 15-195. My issue is that my sash weighs 42 lbs. Your chart tops out at 37 lbs. Would 33F be sufficient?

Michigan Industries single hung alum. Tilt windows Cira 2006. No sticklers, but believe Mi 850 series.Looking for 34" channels, marked 34C. Shoes and tilt lock 3 holed. 2 units of each item.Pls advise $ and deliver (ground) $ and shipping time. Thank you

Hello, I have a Stanley brand double-hung vinyl window with broken pivot shoes and a missing tilt latch. Can you help identify them? I believe the upper part of the pivot shoe is broken off and missing. After looking again the pivot lock shoe I found matching is 15-195. Still not sure about the til ... (cont.)

I'd like to order a window balancer and a shoe for my window and an extra shoe and some other parts, could you tell me what kind of shoe is in the picture and a balancer, thanks

please assist me in identifing my window springs in the picture above

I'm looking for a replacement T-Lock for my standard, builder-model windows. Several have split at the top, rendering the entire lifting mechanism useless. There are only three numbers that I can make out. One is a patent number that circles the cam (PAT# 4610108) and another that is at the top of t ... (cont.)

The spring in our window channel balance popped off and created a mess. The channel itself is 39" and marked with 39B. The slider it attaches to looks to be cracked. I think I need a new balance and whatever the slider is called but I can't find an exact match on the site. Looking to replace both si ... (cont.)

pat4610108....pat6,679,000