Viewing all customer Discussions for:

39-025 Awning Window Crank Operator

The subject operator is depicted in the attached photos with the handle removed and sitting beside it on the windowsill. These are awning style windows from a house built in Broward Count, Florida in 1968. I noticed the window was slightly ajar and when I went to close it, the screw mechanism that t ... (cont.)

Looking to replace an operator. The 39-025 is close. Except 1 1/8 between lower holes. Arm is 2 3/8 between pivot and hole. Also, top hole is slightly off center to the outside. Manufacturer is unknown.

Can you supply this operator? May need several each right & left. Vertical hole spacing 5-1/4", horizontal 1-1/8", end link is 2-3/16" c-c w/10-24 stud, uses screw with shouldered plastic bushing, bushing OD 3/8". Main gear arm is 2-5/8" c-c, end link is flat. Prefer white housing. Could probab ... (cont.)

These are markings on the operator and the operator handle on the inside.Letters and numbers are:WYNN 63.5LAI can't find these anywhere. Not in any hardware store ,not even in Home Depot.Please help.Thank you, William O

I need to Replac an operator need to know what model number it is.

We need to replace the window crank mechanism for an old awning window in our bathroom. See attached pictures. No name on window. number on crank handle is 11-100-11 patent pending. Patent number inside mechanism is 198202US 2RHRD 1963 CAN. Also the arm extension is 5 1/2" inches and has a 'grommet' ... (cont.)

I purchased the Keller window crank, 39-060.The 3 mounting screws are OK but the original oprerator has a bushing instead of a flat arm and also has a plastic sleeve over it. I would like to know if you have the exact part or I should purchase something different.

I have 5 Jalousie Windows on my back enclosed 3 season porch. The Window Crank operator on each window does operate properly. It is extremely difficult to open and close the windows, in fact for two of the windows handle that is part of a worm type insert broke loose from the main body of the Window ... (cont.)

There are no markings or labels anywhere on the pieces or windows that I can read or see. The windows are close to 40 years old they are horizontal and there are four window panels to them. I have nine windows that I need to replace the Cranks for they are all wearing out and in bad shape. Hopeful ... (cont.)

The measurements of the pictured part are the same as part number 39-025 with the exception of the measurement of the two holes at the bottom of the window crank operator. The pictured one seems to measure 1 1/8. Your replacement part measures 1 3/16. There are no marking other than those on the ... (cont.)

I'm looking for a replacement crank assembly.

I need to replace these operators. Can you help?

I have this window crank that broke on the window. The window is very old. Anyone with tips or possible part numbers would greatly be appreciated.

Hi. My issue is the crank is working properly, but the window now only opens slightly then the crank feels like it gets stuck. Forcing the window open past this point by turning feels like it will break something. I am able to close the window, but now cannot open it more than just a crack. Is there ... (cont.)

Attached are pictures with dimension of operator I am looking for, need between 10 and twenty but want to get one first and make sure it works

I thought I was all set to buy an operator from you, but I see that the arm length on center on my unit is 2-1/2". The best I can tell, all your lengths are shorter. I measured from center hole to center of rivet.

Hello, looking for this part Markings are minimal except on the arms, the middle on has a 2 and the extender arm has both 78 and 0. I measured how you folks have yours advertised, and the arm is a 2 5/8" lower screw spacing is 1 1/4 height of unit is 5 1/4 Thank you, Jeff

I am looking for the blanking plastic that goes into the open end of an awning window crank opening.My windows have two possible positions for the crank, naturally one will be left open. I need white approx 5.5" X 7/8"

I ordered the 39-025 but I'm unable to remove the quarter inch size sticking out of the arm. Please see picture.

We have no numbers or marking on the one we need to replace.The one you have on your web site is product code:39-025. This part look close except for the measurement from the screw hole to the rivet .The one on the web page is 2 1/4 our is 2 1/2 will this work.