Viewing all customer Discussions for:

18-009 5/8" Top Sash Guide

This part is for a vertical window that latches to the sash. Attached is a pic. I ordered the wrong dimensions and shape earlier . I need the right part dimension.Ref : 18-185

I will need 16 of the springs. And caps for the top of the windows. 2830z stamped on the part that is 29" long.

Can you please identify

Hi I am looking to replace a channel balance which has the following stamp 33 5 HO Caldwell. Could you please recommend which one should I buy?

Hi this part goes on the window itself at the top and I guess it would be the stop that hits the little c channel at the top of the window runs where the channel balance is attached to

I need one new top sash guide Could it be the 18-200 listed in your catalog? the balance in this window is just over 1/2 inch, probably actually nine sixteenths. It's a 21" tall window that is 46" wide. The number on the balances say Nineteen ninety, but I've already replaced them new ones. ... (cont.)

one of sash top guide is broken (pictures show good on the left and bad on the right with front view and side view) Also show how top guide fitting into the window. The sizes are: Width = 5/8", Length = 1.5" (more in the picture) This is for Milgard window (single hung, non tilt), W ~3.5", total ... (cont.)

I have a window that uses the 27" Series 380 Channel Balance (option 2640). The channel believe is fine, but the plastic part on top of the window (see attached picture) is cracked/broken. There are no markings on it. Can you help me identify the part? The entire piece is approximately 1.5 in long a ... (cont.)

Need to replace stop at top of window that holds the window balance spring assembly in place. See attached photos.

DO you have this part? I looked it up and found out this is called a window balance brake shoe. It sits on top edge of the window. I can't find part. Do you have it? How much? Windows are about 20years old dimensions are 1 3/8" X 1"(top flat part) 5/8" inside part.

I have a Viking metal window made in 1996. 35" by 1/2" balance. I think I need an S395-35. Also a top guide. Present balance stamped 3440. Windows are hard to pull down to shut. Is it possible to get one with less resistance? Thank you, Dan Lind

Hello there, I'm attaching some pictures. I need to replace both balances on a window along with the sash(s) on both sides. You can call or text me if you have any questions. The balance is 26 1/2 inches long this measure is just the metal part and does not include the plastic attachments on both en ... (cont.)

Need your help to identify the right parts for my channel balance. Please include the top and bottom caps. non-tilt, length: 28" width: 1/2" or 9/16" stamp number: 27 4 FP CALDWELL Thank you for your help

Needs a window sash cam with the tabs on the side.

I need to find the correct replacement part of my window balance. The interior cord broke, and the plastic end also broke. The length of the balance (measuring only the metal part) is 24 inches. The width is 5/8 in.

One of my windows is missing this plastic stop on one side. When you push the window down the weight and balance stays up on one side because the plastic piece is missing. I need to order six of these in brown. Please send me a part number if you have them. Measuring from the top side of the window ... (cont.)

I need 12 of the 26 3 do codwell and I need 6 of those 20 3 DK codwell and I need 12 plastic holdersKevin

I have a top sash guide from a 1980s Norandex window that looks similar to the 18-142 but has only one hole instead of two and has a smaller top part. This is similar to other top sashes posted in the discussions. Has anyone been able to use the 181-142 as a replacement for this top sash guide or fo ... (cont.)

HelloPlease advise replacement channel balance for RylockTag on window:MFGR: RYL-017-1SERIES: VS-6AMST: 4-0 x 6-0MVT: 48" x 36"Stamp on channel: 27 4 DQ (or DO) CALDWELLThank you for your help!

Can you please tell me what this part is based on the printing.