Viewing all customer Discussions for:

21-002 Bifold Door Pivot Pin, Benchmark

Ihave the exact same doors. Here are some images of the guides and doors. The metal pins are 3/16" I am missing the glides and white caps and a couple of spring stops. I don't have a clue what they originally came with and how they should work, but would appreciate any input and suggestions for mak ... (cont.)

I need assistance identifying the parts needed for this metal bi fold door. Unfortunately, we do not know the brand of door. Any input would be appreciated. Thanks.

I received bottom track for my metal bifold door, 21-401. Note 2 photos. I think you refer to the pieces as floater and pivot ? Your track is less wide as my old one. My floater piece (under the spring) is wider than the opening on the track and does not go in.I want to order the 2 parts (floate ... (cont.)

Hi! I need your help identifying which parts I need. I have three set of these doors. One on 36 inch tracks and two on 59 inch tracks. I would like to recondition these doors so they open and close nicely. Somebody at swisco showed me the 21-044. The the closest if not the se vracket would ... (cont.)

I am retired woman and will have a handyman do work if parts are still available. The door is 36 inch wide. There are four of these doors in the home. This one is in disrepair. The actual doors are in good shape. I would like to replace all of the other parts. I believe there also should be some typ ... (cont.)

I need top and bottom hardware. All parts pin,spring etc. Please help!

I'm repairing some old metal bi-fold doors for a customer. A cat urinated on the doors and bottom track for years and caused major rust damage. I had to add sheet metal and angle iron to the door bottom. I'm hoping to replace the bottom track with 21-402, and pivot pin 21-002. The upper track has ... (cont.)

I would like to get all new tracks and hardware that sits inside the tracks for my 48" metal bifold closet doors. I have 5/16 inch pins and plan to reuse those. Can you take a look at the attached photos and let me know what you recommend? The bottom track is 1 1/8 inch wide measured from the out ... (cont.)

Hi Frank. I recognize these parts from old Slimfold bi-fold doors. For a bottom threaded pivot pin, see the 21-001. For the guide pin, see our 21-007. The clamp can be replaced with our 21-154. If you need bumpers, see our 21-277. Look over all parts to confirm that they match your old components. W ... (cont.)

Hello The top corner bolt securing door to track is gone. Can you advise what replacement part is needed. Benchmark sticker of brand above

I have two metal bi fold doors that I need all new hardware for. Do you carry? Benchmark doors.

Hello: I need help identifying new hardware for my bifold doors. I need as well new tracks. The old tracks measure 30 inches per one bifold door (4 tracks top and bottom) and 2 feet per bifold doors (4 tracks top and bottom) Thank you for taking the time to help me.

I have a mirrored Benchmark bi-fold door. The hinges had separated from the frame, fixed that. Trouble opening, hinges part of problem. There are two pin holes, pins were in first, on bottom, second on top. Which hole should I use? Track and pins good shape. I wasn't as smart as I thought I was. Doo ... (cont.)

no names, numbers or markings available.

Hi friends,We are facing difficult times with our metal doors in two of our buildings. We are a non profit housing organization called MTR - More Than a Roof Housing Society and we wanna replace our tracks and pins (not the metal doors) by new ones, probably different ones... Today we use parts like ... (cont.)

My PostBenchmark Steel Bifold Door came off the track. The doors are louvred from top to bottom. Need both posts to repair. One came completely off; the other is badly bent. The doors were installed in 1985. The one post looks like the 21-044. Your help is needed to get the correct parts and to ge ... (cont.)

I am trying to source parts for this Benchmark steel bi-fold door. Can you assist --it is installed on a track. will need the parts to hold it in place and open and close smoothly. thanks

I have an old Leigh Metal Bifold door that needs a new bottom track, cap and bumper. Approximate measurements for the existing track are: Length 3' Width 1" Height 15/16". Would your Part 21-401 track be an acceptable replacement and what other parts would I need to finish the set up for the new tra ... (cont.)

Good day. Glad I found your site. I need to replace the 4 pins on each door because the old ones have worn out or broke. The plastic pin holders fall out or are broken. When I tried to reinstall with the old parts it was difficult to place properly. One of the top holders will only move a little way ... (cont.)

We have a Slimfold Closet Door (two folding on each side/ four parts total) which is for our Manufactured House Washer Dryer Closet. The spring/pivot/"gizmo" which is on the track at the bottom, needs replaced, and I have no idea, how to find a part number or anything. The sticker, I saw just had "S ... (cont.)