Viewing all customer Discussions for:

S380-34 34" Series 380 Channel Balance

Hello, The stamp on my channel balance says 33 6 AW CMC 2. Which size should I get? The length is 34 inches and the width is 1/2 inch. Thanks

Hello I have already replaced one of my channel balances and now have had a second one on the same window fail. I replaced the second one with your 385 34" 3320. After install I quickly realized that the 3320 was not the correct strength. (I thought that is what the original was) The sash weighs 33l ... (cont.)

I need to replace my window channel balance. I have three windows. I took 4 pictures. Please let me know the cost of 1 window, shipping cost and shipping time.

Need replacement for the item in the picture 34 inch × 1/2 inch(bit more than 1/2 inch)

Please help identify proper balance for vinyl single open vertical window. Channel width is ~5/8". The channel length from metal to metal measures 34" but markings say #3330. Open and close these kitchen windows many times so these balances have been replaced multiple times. The strings in the pul ... (cont.)

3330

Hi, the windows to my new house have channel balance that looks like "33 5 HQ Caldwell" (winged). Can you please tell me which ones I should order from your site? The measurement (according to the right way to measure) is 34".....Thank you,Ivo

Just bought a house, found two windows with the same channel balances. Most of the windows are missing the channel balances. Found one window with two different size balances. According to your site and the top guide I have rollyson windows but the balances dont look like the 371 balance. They are ... (cont.)

Need help getting the correct parts to order to replace some channel balances.

34 inches long, 1/2 inch wideAfter reviewing my previous order(for another client), I'm thinking the part I need now might be a S385-34. :) Maybe?

Looking for replacement balances for Caldwell 33 4 AQ (34? metal to metal) & Caldwell 27 5 JO (28? metal to metal) Replacement item parts numbers?

I am looking to replace the channel balances on most of my windows as the majority of them are failing. I have attached photos of the balances. There are three window sizes I am working with so there is one of each photographed. The window sizes are (Qty=number of windows): 34"W x 70"H - Qty 10 2 ... (cont.)

33 5 GW CMC 7

Thanks for posting. I think we can replace this balance for you, but I need a little more information to help. Can you show us picture or two of the bottom nylon attachment at a few different angles? I just need to confirm its identity. Many thanks.

Hello, We could use help in selecting the proper replacement channel balance. 34" long, 1/2" wide, pictures attached of the ends and the existing part stamp. Lower half of the window is 25lb, and this is a non-tilt window. Not sure how much I trust the existing part number, as the windows relat ... (cont.)

I need 2 balances with end clips.They are 34" long

This is the channel balance I am looking to replace. I need 2. Thank you.

I have large vistaview window which have a 1/4 opening window in the bottom. They are aluminum and made by kinco. The side cast iron pieces which connect to the metal that retracts the window are broken off. Do you have anything I can replace these with. the windows are 72X36 inches including the bo ... (cont.)

I think I?ve identified I need S380-34. Eveything seems to look good. You?ll notice in one of the photos, there?s a stamped 3320U BSI, However my window weighs 22 pounds. There?s also a picture of weather stripping but didn?t see that on your site. Do you have that or know where I can get it? Th ... (cont.)

HI,My front window sash is broke but I don't want to remove it until I have the replacement part on hand. Can you identify what part number it is from these photos I took while it was installed? If so, thanks in advance for your big help. I will likely order 2 sash springs if that will be better ... (cont.)