Viewing all customer Discussions for:

S380-37 37" Series 380 Channel Balance

Need 2 balance The metal part measures 37 inches 36-15 LA5 CMC (36-HP49-51)

Please help me identify this balancer marked Caldwell 30 3 IMI also need one marked Caldwell36 4 IMI would appreciate if you could spec out the proper one. I miss being able to walk into the old shop. Life goes on. Stay healthy,Frank

Need replacement channel balance. Channel length is 37 inches. Pictures show dual spring, top and bottom hardware, and channel markings.Please advise on the correct part number. Thanks,Maurice

These are 37" long. Need a qty of 5. Please help me find correct replacement item.

Hello I've found out some end guide numbers on another site for my caldwell block and tackle balance, and i was trying to cross compare / validate with your part numbers but can't make a match. i BELIEVE i have 15P142 top guide, and 15P122 bottom guide. Do you have a compatible guide? ... (cont.)

The marking is 3640. I reviewed all the measurements and they seem to align with the Series 380. The dimension that is off is on Winged Channel Balance Shoe. The 1" depth measurement is between 13/16 and 7/8" on my balance shoe piece. Will the 380 series work for me or is there another series? ... (cont.)

I need the part number as I need to place an order for my sliding up down window. This is for 37" window balance channel. It will be appreciated for your quick response. Thank you Rupak

Can you assist in determining which channel balance I should purchase for Rollyson Windows? This is the information on the balance 36 4 DO Caldwell. Thank you

37", long 1/2 " wide stamped on the metal is 3650 BSI

I'm hoping you can help me identify this window balance from an aluminum non tilt window, the metal channel is 1/2" wide, measures 37" long ( metal section only) and has number 3640P stamped on it, I tried to take accurate measurements of the top and bottom shoe, the best I could match it up would b ... (cont.)

I have two windows with balancers that need to be replaced. Both balancers are 33 inches long and I included serial numbers in the photos. The balancers I removed look similar other than the spring is larger in the balancer from the larger window.

Photos show length of 37", back is 1/2", side is 5/8" approximately!Stamped on channel is number "3650". Note end pieces similar to your Series 350, 380, and 385. If tighter measure needed let me know. I have your install guide from your web site. Additional instructions might be helpful.I want t ... (cont.)

need to ID window sash clips and snap in glazing. Using S380-37 balances.Are shorter balances (31")with marking of 30 3 BO Caldwell same as S380-31?

Window decal says hlc 3554 by 96 also h lc50 52 x 76 the balance is 37 in metal to metal

Markings on part say 36 3 IQ Caldwell

I need to replace 37" balances. Looks just like the 380 model. The shoes are both broken so I am estimating I need 1" shoe model although I can only measure 7/8" left on old worn and cracked ones. 22 year old windows. Stamp in channel is 3606. I cannot match that number on your table. These are wide ... (cont.)

Looking for window sash balance.

36 3. F9. Caldwell That's the number stamp ed on the balance The balance is actually 37" long The balance is 6/8ths wide Top plastic piece is 1 1/2" long and 6/8ths wide with the wings 7/8 this wide Bottom wings are 7/8ths wide and 1 1/2" long. Can't find a number that matches any thing online? C ... (cont.)

Old ones broken! No markings or stamps. 37" long, 1/2" (actually 9/16 like you say).

Can you assist with my selection. The stamp on the Channel balance is as follows; 36DS45 The Sash weight is 38.5 lbs The balance length is 37 inches with winged ends on both ends