Viewing all customer Discussions for:

15-191 Heavy Duty Pivot Shoe, 1/2" Thick

A rep asked me how thick is my shoe. It's a little less than a half inch. Thickness is .530 and the width is 1.209 and the sash height is 18 in.These windows are only about 12 years old I don't know why these shoes broke. One broke then the other one, together.Thanks for your help ... (cont.)

Any help would be appreciated. Thank you

Hi, I need help identifying parts to replace the constant balance double coil in my vinyl windows. I can't remember who made the windows, but I think it's either Simonton or Certainteed or some other manufacturer in Richmond, California that's no longer in business.I took a few pictures of the label ... (cont.)

I am looking for the balance springs and covers for this Simonton single hung window. Also, the sliding latch that allows the lower sash to tilt.

Hi, I would like to buy replacement coil balance hardware for a Milgard double hung window. The coils for the upper sash broke as shown in the attached photos. I figure I might as well replace the coils for the lower sash while I'm at it because they probably aren't far behind. The coils for the upp ... (cont.)

What should we reorder? Metal coil is 1/2" wide and has the numbers 246D Z with a 1 under the D and #6.5 354.The gray shoe is 1/2" deep, 1" in length and 1 1/4" wide and has Patent 4,610,108. The white coil housing is 1/2" deep, 1 11/16 in length at it's middle, and 1 1/4" wide and has the numbers ... (cont.)

No description. Hope you can figure out what I need.

I would like to order several of these parts. Can you tell me the part numbers?Norm Thank you!

2002 double coil balancer

Part #801020 on white plastic #5.5 on coil 5232208 Can't see numbers on second coil Shoe 4,610,108 possible patent number

Hello, I am looking for parts for single hung Simonton vinyl windows approx. 24 yrs old. Needed are pivot shoes and bars, tilt latches, balances and springs. Forgot to add to photos- pivot shoes are 1/2" thick and tilt latches are 7/16" thick overall. Springs are 13/32" thick. Visible #s on spri ... (cont.)

I'm looking for some pivot shoes to replace some where the tabs that hold the coil have broken. I could also use a couple of coils. The coil style I appear to have is an S160 (tab on the end that clips into the pivot shoe). I'm fine with purchasing a kit containing both a coil and a pivot shoe. The ... (cont.)

Can you please help me identify this?

Hey there! I also need a pivot pin replacement for a single coil balance. One of them fell out and was lost. The tooth is 7/16"

Hi, Have no marking on old coils. Cassette at top of sash housed double coils on both side. The length of the sash from the bottom of the cassette housing at the top of the sash to where the shoe with the window closed is 53". The window weighs 20lb. Wish to buy the entire balance assembly (casset ... (cont.)

Good Morning! Attached are some pictures of the parts that were removed from a window at one of our properties. Can you help identify the replacement parts for this? Thanks Jamie

Window not holding up . Keep going down .

Is there a product I can install to replace the old balances. The old ones are broken and will probably need to be cut in order to remove. The rail opening is 3/4" wide and 1/2" deep. The sash is 25 1/2" wide by 29" high.Thank you for your assistance.Wayne

Balance coils on upper sash are broken and I am seeking replacement parts. Window (0607.jpg) is approximately 2' x 3' and in generally good condition. Part Number shown in 0609.jpg. Broken coil showing attachment tang in 0611.jpg. Thanks, Richard

Hi - Do you have the window pin that goes into this product? https://www.swisco.com/Heavy-Duty-Pivot-Lock-Shoe/pd/Tilt-Window-Replacement-Pivot-Lock-Shoes/15-191 Thank You,