Viewing all customer Discussions for:

39-533 11-3/8" Casement Operator Track, 3 Hole

I need this crank assembly. 4.5" arm. 6" arm. 8.5" arm.

Looking to replace 3 window cranks on windows. They are Polaris windows.

I am looking for a left and a right operator for casement windows. I am having a hard time locating these. The arm length is showing as 11" if measure from the mechanism and if measured from the elbow to the end it measures 9 1/2".

I need replacements for both right and left. Inside cover reads Biltbest Part 233 D.C.

The Cardco window crank extension arm is bent. The long arm is 12" to the angle. The short arm is 5".

I'm looking for this part of window

Looking for replacement hardware for two (left opening and right opening) Norco window crank openers. Not sure how old these windows are. The hardware is marked "Truth Entrygard". Not sure these match your part # 39-031 and 39-032 as the shorter arm, stamped 20755, measures 3 7/8" and said part actu ... (cont.)

before I start replacing the hinges with products from your company, I was hopeful you would guide me on how to adjust the crestline casement window. As you can see from the photo the bottom part of the window is not flush with the casement- I have included photos of the gap, hinges etc. I have a nu ... (cont.)

Crank threads are stripped, window opens but can't close by crank. Hoping to go through and replace all in house. Windows ordered by previous homeowners so don't know anything more.

Window crank match.

Hello, I have six casement windows (three right, three left) that have problems with the operators. For the most part, the issue is that the arm falls out of the track on the sash when attempting to open/close the window. In two of the windows the crank no longer moves the arm. Photos with measur ... (cont.)

Hello,I have ordered a bunch of the casement windows operators and all of them have been great! The contractor we are using on this last window, the track is missing, so he took some pictures and even measured the area we are missing. In speaking with Deb this morning in customer service she started ... (cont.)

The pictures are of the right side. I need the left if looking at it from outside. It is way broken. Crank broke too. Don't think I can open it.Numbers on it DEPRES-???DETA ??Also says entry gard Truth29810

I have successfully identified most of the items I need for my order. However, I'm concerned about the Ellipse Style single arm operator. I believe that product 39-028E would work (9.5-inch arm) but I'm not certain the interior covering would cover the opening completely. My current window has a s ... (cont.)

Good Morning, I need a replacement part for a Marvin window that is 30 years old. I have attached 2 pictures of the window hardware as well as a sheet showing measurements and part markings. The current part fits in an opening 5 inches wide. It has numbers 89 and 43 on it. Other Truth parts have n ... (cont.)

These are Kolbe & Kolbe windows manufactured in 1999. They are 22" x 46"

I am looking for casement window cranks for left and right opening windows. The following markings are on the original crank: 45035-RH, TRUTH, RH, 3.

These were Peachtree windows that were put in about 35 years ago. As you can see from the photos it opens out to the left. The number on the mechanism is 2081. And the wrds on the mechanism are Entry Gard TRUTH

Hello. We have 2 clad case master Marvin windows. The cranks (part number 10898240 ) no longer work. They are discontinued. There may also be a problem with the operator too. When the cranks did work, we could get the window to open. However, to close the window you'd have to lean on it from the out ... (cont.)

It is stamped Truth Entry Guard, and has gears similar to 39-036, but the operator's arms and link arms look different.