Viewing all customer Discussions for:

S385-27 27" Series 385 Channel Balance

I am unable to identify this balancer. The imprint on the balancer shows "26 5 IW CMC 11".

My channel balance Stamp is 26-4 LU CMS 1, the metal size is 27" I need 2. ? is part 27" series 350 channel balance S350-27 option 2640 the right part for me. Thanks

(Scale gave wrong result when on carpet) Correct weight: 24.3# Milgard Marking 26 4 LV CMC 7 Is a replacement upper retaining clip available? (Original slightly bent.) How is clip removed and replaced. Thank you

Please help me identify these 1/2" spring balance: I believe these are S385 balances as the bottom shoe appears to be the 15-004 as it is 1-3/32" deep. One of the 27" long channels is marked 26 5 LN CALDWELL The other 27" long channel is marked 26 4 JN CALDWELL The 21" long channel is marked 20 ... (cont.)

Hello, Need some help pinning down the correct balance for a Kinro window. Part stamp is included in the one of the pictures. Overall length including the plastic footers that are pinned in place is 28". Thanks in advance!

27" long channel Markings: 26-3 FK5 CMC 43

The side of my sash says 26 4 GN Caldwell. How can I tell how much tension I need ? I do not have a scale.

I am looking for a replacement window balance for a Kinro window I have. The length of the channel is 27 inches. The lower plastic piece appears to be 1 and 3/32". The spring has a green paint mark in the middle of it. The printed number on the channel is 26-3 KN5 CMC 8

Hello, I am looking to get an accurate identification number for the following channel balance that I am looking to replace. 27" overall length of just the metal bracket. 1 1/8" balance shoe. 26 9 KQ Caldwell is written on the metal bracket. Thank you!

I am looking for channel balances marked 26 4 IU CMC 2

July 28, 2023Please find attached details of my window balancer.* Printed on the lower end of the channel: 26-9 CS CALDWELL* The five attached photos represent one of two two window-channel balancers needed.* Total length of both channels, EXCLUDING the plastic parts at each end: 68.7 cm / 27.04 i ... (cont.)

Hopping you Have this ChannelsItem number has mark on the side of the channels27" Channelshas has mark on it horizontal 26 4 & Vertital BSI and Horizontal PPand 12" Channelshas has mark on it horizontal 11 5 & Vertital BSI and Horizontal PNI am assuming the first 3 numbers are the size of th ... (cont.)

My window channel is 27 inches long not counting the plastic ends and 1/2 inch wide. The marking stamped into the metal is 2630 CJ @ NE. I would like to purchase a new Ballance but I am not sure which one I should buy. Please tell me the Window Ballance I have and which one I should buy. Thank You, ... (cont.)

I have a Caldwell Manufacturing non-tilt balance that needs to be replaced. The photos of the end caps are attached. The length of the aluminum rail (not including the plastic end caps) is 26-15/16". The part number stamp is: 26 5 CX CMC 7. Can you please help me find the replacement part for th ... (cont.)

Channel length: 27 inches Stamp: 26 4 GW CMC 7 Manufacturer: Milgard (approximately 2003) One balance definitely needs replacing. But I have heard I should replace the other balance too. Therefore two needed.

Home was built in the early 90s. They are 1/2 wide and 27" long.

The part measures 27 inches, 26 4 GN Caldwell

15" Series 385 Channel Balance, 1420 for Option Will This Fit? Please verify. Thank you. See attached photos.

I'm trying to find a replacement part of a window balance. The stamp on the back of it reads 264 AW CMC 2. Can you please link me to the Swisco replacement?

Please help me find the part number for the balancer to order for my Milgard single-hung window: width: 1/2 inches length: 27 inches weight of hung window: 19 lb If you need further information, I'll try to get them. I greatly appreciate your help. Thank you and have a great day. Louise ... (cont.)