Viewing all customer Discussions for:

S385-28 28" Series 385 Channel Balance

I have a channel balance that has a length of 28 3/4" metal end to metal end. it has nowinged guides o the plastic ends

I need to of these plus two that the metal measured 10" the load number is 3 both have the same ends with wings

Hello, I need help identifying the correct balance top for my channel balance. I cannot locate the black balance top on your website. See the attached pictures. My channel balance details. 1) Non tilt window. 2) 1/2 channel width 3) 28" long 4) 2740 stamp 5) Window weight approx 24 pounds T ... (cont.)

I need to replace my channel balances on my non tilt window. It has this on the balance: 27 4 GX CMC 11 The metal piece is 28 inches long and has plastic ends attached. Please see photos.

Please advise on pricing and availability for replacement channel balance for my windows. The balances in the windows are 27 3 FQ Caldwell and some are 27 4 LP Caldwell. I have attached pictures of the ends.

I am trying to find the correct channel balance to order. The stamp on the balance says 27 5 BSI NG Metal length is 28" Width is approx 9/16 Picture of the top and bottom fittings attached. Thanks for your help!

I have a "27 3 JQ Caldwell", which balance channel should I use to replace it. Thanks.

Need help identifying window channel balance replacement for non-tilt Rollyson aluminum windows. My larger/wider windows have a 27 4 FL Caldwell stamp on the existing channel balances. The narrower windows have a 27 4 EL Caldwell stamp on them. Both channel balances are 28" long and 1/2" wide. W ... (cont.)

Need your help to identify the correct replacement part number for the 28in and 34in channel balance per the attached pictures. At your convenience could you provide the replacement P/N? Need to buy 2 pieces of each.

Looking for some assistance identifying the correct channel balance. Photos attached. Measurement is 28". Thanks in advance!

I am looking for 4 pairs of 2740S model balances. Please see attached images and let me know if it is same as model 2740

Looking for a replacement channel balance for a Jeld-wen window. The balance has "27 4 CV CMC 7" stamped on it.

My current balance has a stamp of 17 4 KP Caldwell, which I figure is for the 2740 sash. I weighed the sash and it weighs 12-1/2 lbs. Should I still order the 2740 or something lighter? Thanks.

Channel Balance Part Identify...This is the part we think it is (listed below). Could you please help us to verify. Thanks!28" SERIES 385 CHANNEL BALANCEProduct Code: S385-28Option: 2740The Balance is 28" (not including the end clips). The depth of the shoe clip is 1-3/32". The stamp on the old part ... (cont.)

18"Pls teach me which part I need to buy?Thank you so much

Metal is 28" long. 2730 stamped.

Greetings from CA!Saw another customer's post with this/my same model # on his channel. Wasn't sure if our the ends were the same and if what you recommended for him (S385-28) would also work for me. Could you please look at my ends and suggest which of your replacement channel balances will work f ... (cont.)

My 28" SERIES 385 CHANNEL BALANCE has 27 C stamped in it. Do you know the strength I need from that or do I need to weigh my sash?

My channel balance is in good shape but the cord snapped. Where do I find replacement cord and how do I know how long it should be?

My windows are the original ones .. in good shape through many storms but I cannot open many of them because the inside clips have become dysfunctional.. as well as the other part(s)... it?s hard to diagnose because the window may fall out. What parts can remedy this? .. without total window repla ... (cont.)