Viewing all customer Discussions for:

S140-07 7 lb Series 140 Quick-Tilt, Single

Hello, I'm hoping to find a replacement for these window coils. I believe the coils have snapped, which is why I don't have any pictures of how the parts are installed before they were broken. The only markings on the parts are "7R". My window is approximately 13 pounds. I couldn't find parts that l ... (cont.)

I am looking for window balancer as per attached photo. The size is as follows: 4-1/2"(L) x 1-1/4"(W) x 1/2"(D) Weight of one window: 14.4 Lbs Please let me know the part number I need to order.

I'd like to replace all locking terminal or shoe with a new one. The only numbers that I found on these old shoes were 8 and 7R.

Hi, I am looking for a Coil Balance assembly. The only information that I have is a number 7 stamped on the coil.The coil and assembly are 1/2 inch wide. It's from a single hung bathroom window and both coils are broken. I have attached pictures of the assembly. Thanks!Bob

Hi I opened windows for cleaning and it stock. It than happened on the 2nd window I tried to look up. One side was stuck while other was still moving. While truing to force windows to close I broke two metal cams and black stops on top, that look like your TAMP-R-LOK III. Need replacement for 2 to ... (cont.)

Bil-Ray Sears - 2300 double hung windows, order #148,970, lot# 57,349, need balance shoe and balance assembly springsHi, I purchased windows from Bil Ray Aluminum Sliding contracted by Sears 15 years ago and they went out of business. I will like to know if you can assist me with the parts I need. ... (cont.)

I cannot find the complete part should I just replace the coil? What part or parts are required

What weight balancer do I need?

No name

I tried opening my window and it was stuck. I pushed a little and heard a snap and now it won't open all the way. When I tilt the window out this is what I see. Can I replace this part and if so what is it?

have accu-weld windows series 2100.. need replacement parts for 2 of my windows. the part on side of window that helps them go up and down. looks like a metal gear inside. and plastic part that you push to the side so that you can tilt window down. parts need two of each.

Hi I have a Camelot/ Crusader double hung window circa 2009 model VSDH that wont stay up I suspect the coil balance has broken I can see the coil What coil balance and shoe replacement part do you recommend? Thank you in advance.

I ordered the balancer 140, your site shows left and right, my question is left side facing the window from the inside?

Purchased above item from you. Was wondering if there is a video on how to install. Appears to be larger than broken one. Thank you Jackie S.

What pivot bars do I need for S 140 coil balances? I just purchased 5 lb s140 and 7 lb s140 constant force balance systems for my old tilt out vinyl sash windows that work nicely. Unfortunately i need the pivot bars that fit these. The pivot bars on my windows don't fit down into these. Please help. ... (cont.)

Hello, Will you be kind to tell me if you carry this parts for my window.

Good Afternoon, would like to know if you sell replacement parts for tilt out windows. Photo shows piece or pieces needed for both sides of the window. Please advise. The round piece along with the flat piece in photo are the parts that I am looking for. The window cannot be raised without falling d ... (cont.)

Pictures attached. One spring is labelled 6Y and the other is labelled 7Y. They are 1/2" wide. I need order information for EVERY item shown here, for both sides of the window. Including the pivot bars that go into the bottom of the window. If this can be bought as a complete kit, that's my pre ... (cont.)

Hope you find pictures and measurements helpful. Thank you, Chris

I have a vinyl replacement window where the coil balances have snapped on both sides