Viewing all customer Discussions for:

39-396 LH 12-1/8" Hinge Arm Assembly, Pella

Can anyone tell me the part I'm looking for? It is for a Pella casement window. Do not see any markings or numbers on it

Do you know where I might be able to obtain an 11" Pella hinge arm assembly similar to the 10" you carry

We have older Pella windows 1976 vintage. The opening mechanism has two rollers at the bottom which should allow the window to be cranked open. The rollers must have worn to the amount that they no longer hold the support shoe to remain clear of the window frame. The support shoe drags on the wind ... (cont.)

I have Pella Casement windows. They don't close properly without me pushing them closed. I've determined that they have the Pella roto opener (1967-1993). The openers are quite expensive, and don't seem to have any adjustments. But I'm wondering about the support arms that aren't attached to the ope ... (cont.)

can I get your help so I can order the correct window hinge. I measured the long arm and it is (11 and 5/8) from end to end. You can respond via email I've attached some photos below.

Purchased part 39-394 but my hinge arm has difference in length of 1 3/4. Solutions

Hello - I have Pella casement windows from 1980s or so.... I need to replace the HINGE ARM ASSEMBLY on a couple of them. However, according to my measurements, mine seem to be the 11 inch size hinge arms. Do you carry this size? If not, can I use the 10 inch or 12 inch to do the same job? Thank ... (cont.)

The support arm bolt broke. I don't believe i need a whole apparatus, but I don't know. Pella is the absolute worst! Any help would be welcome! No model # because they were geniuses and put them on stickers then, which were removed before I bought the house. Window still opens. This is tge tight s ... (cont.)

Hello, Are you able to help me replace the operator on an older Pella window? The photos attached are for the left window, I need the operator for the opposite, right window. I also need the wood molding cover. It's 31 1/4" Long. The sash size for reference is approximately 33 1/2" W x 56" H I a ... (cont.)

Hello, Can you identify this operator based on the attached pics? Thank you in advance, Tibor B

Today I received my order: #939109 Item #39-396LH 12-1/8

Looking for slide rollers (part name?) for Pella casement windows that are probably 30 years old. The windows are wood with a vinyl clad exterior. This part slides along with top and bottom window sash when you crank the window open. Any help is appreciated.

I have a customer with 6 pella windows and she needs all new hardware Hinges and the sash operators. The sash crank operators are part # 39-175 and 39-176. The arm connecting the hinge is 11". Do you guys have those or can I make the 10" or 12" ones work

Does any of your Pella casement 1 piece Bottom Hinge fit my Pella wood casement window vintage 1978, Bottom 2 piece Hinge with White Plastic Pivot Hinge with rollers? Also how do I order the white plastic pivot hinge pcs for left or right opening windows? These parts are left or right specific. I ... (cont.)

Do you stock the 11 inch hinge arm assembly for pella similar to your socked item below? RH 9-5/8" Hinge Arm Assembly, Pella Product Code: 39-352

Hello I need help identifying this Part! I have look and tried everywhere! I need to know as soon as possible! Thank you so much

I'm looking for a Hinge Arm for a 1980 pella casement window. It is approx. 4-1/2 long and 1/2" wide. The Nylon hinge shoe attaches to this part. The window is 28x48 and opens inside out from right to left.

Hello Swisco, I am looking for a very similar Pella casement hinge as the 39-352, except the long pivot arm needs to measure 12 1/8 inches end to end. The sash it operates on is 34 inches wide.Is this available? Thank you! BTW, Great web site !! :)

Can you identify the hinge arm in the attached photo. We need (1) RH and (1) LH please.