Viewing all customer Discussions for:

S180-08 8 lbs Series 180 Coil Balance

No markings on coil for LB s. 1.5 in wide. 1/2 in or 9/16 thick. Looks like your s180 spring. Single coil. Need about 10.

My coil balance are broken, do I need to buy the set or just the coil, and it looks like it's #8. Thanks Dennis

no mark on spring have on mark on lock wherepin from window locks in. (8R)

Hi, need help replacing the constant force spring assembly. The window weight is 30 pounds, so I'm looking at the 15-lb/pd/series-140-quick-tilt-balance which looks totally different from what I have I also need the rounded pivot bar. Is there any parts I need for attaching?

I believe this is called a constant force spring.It is broken in one of my other windows and I need to replace it.

I need 20 of these to start

Wondering what coil I would need in order to replace the ones on my window that snapped. It reads 8EB on the side as seen in the photo. Thanks! Ryan

Good day, I am looking to replace ALL the coil balances/housing pivots to my windows and just wanted to verify the exact parts I need. I have four windows that are 25 27/32 W X 23 23/32 H. I would like to replace the top and bottom, left and right balances/housing pivots. I have three other wind ... (cont.)

I have a Thermaweld window which was installed in 2010. The window won't stay open. The only information I have is the Coil with a number 8DF engraved on the coil. It is a double hung tilt window. Will 8 LB SERIES 140 QUICK-TILT, SINGLE Product Code: S140-8 possibly fit to replace the coil bal ... (cont.)

pat.5,353,548i have these constant force balances throughout my house. many of them snap up when you take sash out for cleaning. i measured the square footage of the bottom sash. i have ten windows, and i came up with 3 weights. 6 bottom sash weigh 21.4 lbs. 2 sash weigh 18.2 lbs.2 sash weigh 15 lbs ... (cont.)

I need two constant force balance springs for a Royal Prime window. What part number do I need and where can I find it?

Window cannot go up or down. Need to replace window balance. Please let me know the parts I need to replace both sides of the window?s balance. The window measures 35 x 45 (width x height) on the outside frame.

Hello, I need to replace two broken sash support coil balances and worn coil housing pivots for both sides of a small bathroom window, please. The upper tilting window that needs the replacement parts weighs 13 pounds. The old broken spring coil balances are 15/32" wide. As seen in the attached ... (cont.)

the only numbers i could find were the following: 1257801 52-8506-wht

Gorell 5305 double hung windows Both coils broke . They have Stamp into coil 8 AE near the top by the 2 holes

the window is 44 pounds, vinyl frame. the existing balances appear to be 35/64" deep by 1- 17/64" wide with 3 coils. I inadvertently damaged them while installing the window. Have been unable to contact Crestline. I need 2 pair, plus do you have a spreader tool to remove/install them? Thank you, ... (cont.)

I need the coil window spring balance with 1/2 high 2 1/2 my # 917

Please help me locate this part.Pat5,353,548 stamped on side.Two of the tandem housings are marked 7 and end housing is marked 8.I need the coil springs also

Can you identify this type of coil balance Thanks Gerald

To whom it may concern, I have a broken coil and believe its a Series 180 and I do not know how to remove it from the track to service once I order parts. There is no notch cut out or access port like others described in the window frame. These windows are purchased from Gienow windows in 2000-2 ... (cont.)