Viewing all customer Discussions for:

15-002 Channel Balance Shoe, 1" Depth

Hello, I have two different channel balances where the metal channel of each are not whole numbers. One balance is 17-1/2" and the other is 21-1/2". Please let me know if this needs to be custom or if additional information is needed.

Good Morning,Please help me identify this item.I will need a complete set for two windows.The length is 24"Thank You.Gus

Non-tilt window Channel: 30" length, 1/2" width, marking: 29 2 ER CALDWELL Top guide: winged Bottom shoe: not winged measures 1" (I think matches 15-002)

I need (10) S351-20 option: 1910 with 19-010 shoe option on top

Need window valances for 1997 Kinco windows. Stamped "29 4 IQ CALDWELL", see.picsThanksJohn

I need help identifying the right channel balance to order. The closest I found was S370. The bottom shoe looks like an exact match, but the top doesn't quite match because it has wings. Here are some pictures attached below. Total length is 25", channel is 1/2" and tension/weight is 2430. (Not ... (cont.)

Hello. I am working on my condo and only 1 balance is left in all the windows and it appears to be broken on 1 end so I haven't been able to identify it. Rod itself is 30 inches with #2920 on it. Pictures of both ends attached. The T shaped one is the broken (I assume) one. The fang tooth one look ... (cont.)

Channel balance series: S351 Channel length: 42" Channel stamp: 4190 P44 Quantity: ? Comments: NEED QUOTE

Channel balance series: S370 Channel length: 47 Channel stamp: 4630 Quantity: 4 Comments:

Channel is 1/2" wide and 26" in length. It are easily 27 years old. I'm not 100% sure but I think the plastic parts are 19-002 and 15-002 but I'd like confirmation before ordering a bunch of these to replace in my house.

Need help in finding the proper guides. Windows are all the same height from frame to frame edge. The top side is pointed with tiny wings. The bottom. Edge rounded.

Hi, I have a balance that is stamped 2330 the metal part measures 24 inches. It has a 350 series top and a 370 series bottom. Do you sell something like this, I didn't see it on your website. Also the metal piece measures 1/2 inch. Thank you Greg

Hi,Photo is of a window balance, part # 2830A. Balance is 5/8th of an inch x 29 inchesDo you have two of those and two take out clips in stock? If so, what is the cost?Thank you,Jeff

The calibration # is 2310. I have attached numerous photos for your review. I will need 2 pairs as replacements. Look forward to hearing from you.

Loose Window weights about 40lbs. Impact window. This looks like the 377, but no little fins on the bottom shoe. Not sure if that's important. Looking for 10 on these. Let me know what you think. 30" length, so thinking the 2960? Thanks

Length is 31 inches Stamp 3020 Windows were made in the late 70s I need 8 balances Thank you!

I have identified this as the series 390 channel balance. I'm not sure how to read the weight rating from the stamp: 22 9 GX CMC 11

Please assist in identifying the correct Balance to replace the attached. The length measures 23" not including the end caps. It has a marking that reads (h 22-5). The ends were referred to as a safety end on one side and a KK end on the other.

Need to know what the replacement is for this non-tilt balance - width is a half inch and length of metal part id 22 inches. I can't find the anything on your website that looks like the top part. The stamping reads 2110.

I want to confirm I am ordering the correct parts. Would you be able to tell me which channels to buy?