Viewing all customer Discussions for:

15-029 Winged Channel Balance Shoe, 7/8" Depth

Need 2 of them + the take out clips teh description I found is 2740 BS1 00 . Is a 28 inches long metal part bottom plastic part measure 1 inch Could you help me finding the right replacements Thank you

I need help identifying correct replacement for a Caldwell 27 2 ES channel balance. Balance length (steel only) 28", bottom shoe depth 7/8", sash weight 17.5 pounds

I need help with identifying which tracks I need for my window. Tracks i removed measure 39” long and have a “3940” stamped onto them. Unfortunately both plastic ends of tracks are completely broken off.

Not sure what 15-XXX it would be. Thanks for the help.

I have some old wooden sash with broken balancers. I'd like to talk to someone about easiest way to reinstall balancers. Sash won't come out until I remove wooden trim stop that retains sash in frame. It won't fit over balancers so must be installed in sash to install. Any hints for holding balance ... (cont.)

The plastic corner on the window pane that moves up and down held on with 2 screws. Appears to help guide the pane up and down against the balance.

This is a 14" window block and tackle, measured metal only. The bottom plastic is different from the ones that come up on my search. There was only one in this window when I removed the sash, and this one just fell out. Not even sure it's original for this window, since it's an odd shaped end, an ... (cont.)

The metal channel is 28" long. The metal channel width = 5/8". The plastic foot at bottom = 7/8" wide. The metal channel has the following markings: 27-4 J15 cmc50

What replacement balancers should I order? It says 2120, measures 22" in length and the bottom piece is a bit less than 1"

I believe this is a pan am 1820z channel balance. 18.5 inch. I also need the piece that fits on top of the window.

I need4 black ones and 4 white ones Thank you.

Hello, I am disappointed to find out that I also need smaller bottom fittings. I recently ordered 24 of the 30" 380 series because this website said to compensate for wear when measuring the old channel balances. The 380 series with 1" depth does not fit, so I'm tempted to shave them down with a dre ... (cont.)

I have a non-tilt channel balance with a stamp of 2920 BSI. It appears to be a 380 with a 15-005 bottom fitting. However, is the 1" depth for the 005 fitting a nominal dimension or actual? My fitting measures about 7/8" - see uploaded picture.

I believe there are wings on both ends. Can you please advise part number for these. Thank you. I am measuring 7/8” for shoe depth? The sash weighs 16-17 lbs and the sash guide 18-161 is the correct replacement. Thank you for your help and have a great day.

I figured that these are s380 rails 29” long. But the only stamp on them is 28C so not sure on the weight rating to pick. Aaron

Looking for exact replacement for window balance. One side string broke so just looking to replace both. 2630 is stamped but that's it. See photos attached

I need to replace my window BALANCES.The stamp is 3406 but it is not in your chart, please assist.

The original balance in the pictures I provided says 28b on it and is 29" long. A window person replaced some on a simple window and they say 28-2 Fq5-cmc 21. The plastic guide wings are the issue as I cannot seem to find a rod that includes the guide wings that are on my original balance rod. The g ... (cont.)

I would like to replace some of my original window channel balances and am looking to identify the correct replacement. The metal channel is 24" long and the channel is stamped with "2310". Below the stamp is the letters "BSI". I have included photos. Thanks.

Need help identifying correct balance, particularly the shoe as it's geometry is a little different than all the shoes on your website. Window weight is 18 lbs. Any help is most appreciated.