Viewing all customer Discussions for:

39-060 Keller Window Crank

Please identify this part and I will buy a new one to replace it. Please let me know if you need more information

This is the part that is on the side of every window pane frame that projects from the edge of the frame that when you close the window sits under the claw in the mechanism and locks the window as the crank is turned and draws the window up and in.

Hi, the part is plastic and it breaks so it can no longer hold the metal hook. Do you have anything like this? Thanks

Hello, I am needing a RH crank system for my old house windows. It has serial numbers etc PAT.NO. 198202 U.S, 2 RH,RD, 1963 CAN. If you need any other information please email me Regards Charlene

Have casement windows in my atrium, house is 30+ yrs old and I've owned only 8 so have no idea who made windows. Had one crank replaced by local co. but the service was horrid. Need to replace 1 left and one right had crank, thus 2 cranks. I measured 5"1/4 for the body of the device. Silver. Ho ... (cont.)

5 1/4 inch tall 1 1/8 inch between screw holes at bottom Screw hole at top offset towards side 2 5/16 between holes on arm 3/16 hole at end of arm

Crank is located on left side of window it operates. Handle seems to Have stripped inside so I need entire assembly.

there are three screw holes to hold the crank case-- top left and a little above right bottom. there are 23 crank cases in the house and some of the screw aren't holding. they appear to be a 3/8 inch across. should i be using bigger screws to hold or somekind of self tightening if they make them. s ... (cont.)

5 1/2" upper & lower mounting hole 2" bottom plate with 2 screws 5/8" between screws Length of arms: Top 4" Middle 10" Bottom 4" That's the best I can do

I a not sure what to buy here are pictures. Of the items a operator and a Broken latch piece on the window itself

I recently purchased a Keller window crank 39-060 from you. After comparing the actual part to the one i'm trying to replace I found that the L-shaped mounting area is the same in terms of hole spacing etc, but noticed that the 39-060 has an extra crank leg attached to the gear/leg piece. My part ... (cont.)

Can you tell us what the distance between screw holes is, from top to bottom? This will allow our parts experts to better recommend replacement options.

Take a look at our 39-060 operator, compare the dimensions of your operator to the picture below, and see if this part will work for you. If the dimensions do not match, please submit your dimensions and we will do our best to find you a replacement option.

Hello,WE'd be happy to help but it's tough for us to narrow down your replacement options without seeing the arms that move the window. We'd have a much better chance of finding the correct replacement for you if you could show us a picture of the operator removed form the window with a clear view o ... (cont.)

need bronze replacement awning window operators and am not sure which one will fit. Frame has the name "PGT". Need 5 left and 5 right.

The house was built in 1968 in Fort Myers, Florida. Some have stripped gears internally. We want to replace all 11 window cranks.

Just looking for replacement cranks on the right. Thank you!

the controller arm's screw hole is small.

I just bought a house full of awning windows. Several have stripped handles. I think your site might have the right size. Could you please look at these photos and tell me if the 39-025 and 026 are the right ones? If so I might start with two of each (in bronze) to make sure they will work. I?m not ... (cont.)

The subject operator is depicted in the attached photos with the handle removed and sitting beside it on the windowsill. These are awning style windows from a house built in Broward Count, Florida in 1968. I noticed the window was slightly ajar and when I went to close it, the screw mechanism that t ... (cont.)