Viewing all customer Discussions for:

Door & Window

I need a pair of replacement window channel balances--this will probably be a custom order Here is the basic info: Length: 28" Width: 1/2" Label: 27 4 HP Caldwell Window type: Non-tilt Only the bottom sash opens Attached are pictures of its top and shoe; the shoe has wings.

Ryan Homes built my home in 1999 and used the Patriot Single Hung Series 2000 Windows. The label on the window states: Mfr stipulates conformance to NFRC100/200/300/301 Code: PAT-086 Spec NFRC Series NC1800 MST 4060 PAT-086-U107-87 My window will not go up anymore the spiral balance with red ... (cont.)

We need a new crank assembly for one of your windows (truth weather Gard) The broken one is left-opening (hinge on left when viewed from the exterior. It is mounted in an opening 5"wide. On the opposite side (the good one) there is 20810 stamped on the arm and also r30842. We also have stubby crank ... (cont.)

My window crank is broken and I need a new crank mechanism. I looked at your cranks and the one that appears to be correct for the window that I have (photos enclosed) is model number 39-020. Am I ordering the correct part number along with the 39-520, 39-205, and 39-107 parts. Please respond s ... (cont.)

I need balances for 25= year old Alenco window. The channel is 22 inches long, 9/16 wide and 5/8 deep. It has "21 C" stamped on the channel. I replaced a longer version of this one a few years ago that is a little less than 28 inches in length. It has the number 2720 stamped on it and was purchased ... (cont.)

I have older Anderson windows in my home, Narrowline I believe. I am looking to replace many of the spring sash balances. The number stamped on one of the balance boxes is D9 7P 27 474. That is for a double hung wood window which is double payned. Measurable glass visible is 28 1/4"W x 20"H top ... (cont.)

I cannot find any identification on our slider door or screen. After studying your rollers, we have something that looks like 84-002M. When I pry the wheels down (which are broken), it gives and feels like a spring. I cannot see any screw holding the wheel in place. When I pull on it to try and sli ... (cont.)

Need to know if you have these in left and right hand. Thanks Gary The stamp on the operator is C-9400-1

The window is a Philips 800 series vinyl window. It has the following printed on it 29 6 LW CMC 11. It measures 1/2" x 30". Which channel balance do I need? Pictures attached. Thanks...Craig

I need the 8 inch, or so, t-limit arm that goes with these hinges. It is missing on a window that also needs an operator, hinge is on ther right.

Have Gapco windows and need replacement channel balances. The channel balance has a stamp with the number 3430 stamped in the balance, additionally it measures 35in. in length

Hi, I have an Andersen sash balance stamped with the following numbers: D72 7#27 8-78 In total I need 8 of these units if you have them available and can give me the cost. Thank you, Chris

Looks like I have a 9400 Split arm crank that is no longer available and is replaced with your 39-264, but before I order please review my pictures. Thanks, johnO

I need to possibly replace a few channel balances in my windows. The sash guides have broken and the channel balances become non-functional. I don't know whether just to replace the sash guides or the channel balances or both. Can you recommend what is needed? Attached are pictures of the brok ... (cont.)

I HAVE A SASH COUNTERBALANCE WITH A NUMBER ON IT AS FOLLOWS. E50 9#27 10 77. WHAT WOULD THE REPLACEMENT PART NUMBER BE?

I ordered part # 90-009 but the part of the lock which makes contact with the window is too short so that it doesn't reach and make contact. Therefore, these locks won't lock the windows at all. Is there a part that has a slightly longer locking mechanism that will work?

Here's what I think I need, and they don't seem to be a normal stock item: 1/2 inch balances for old non-tilt single hung aluminum windows. Length is 23 inches Sash guides are 18-009 Shoe appears to be 15-001 Top appears to be 19-005 Option 2230 Pictures attached. I'd like to order two to ... (cont.)

Hello, I need to buy a new window channel balance and i went through the steps on this site but i need to verify it before i buy it. To start of: 1) This is for a sliding window (up and down), so non-tilt. 2) When the site asks me if it's a 1/2 or 3/8, what I'm seeing on mine that it's 5/8 ... (cont.)

I had vinyl replacement windows put in my house 12 years or so ago at 2 different times; the one batch seem to open easier than the others that usually require 2 hands to open/close. I'm anticipating replacing the balances to see if that helps (I believe 24" series 900). Thoughts? I was told to tr ... (cont.)

I need to replace two window cranks (one RH and other LH) at my house. I see a few cranks on your website. How can I determine which is the correct one for me. Going by the number and positions of the fastening screws and their relative positions, the Model 39-016 appears to be the correct LH crank ... (cont.)