Viewing all customer Discussions for:

15-150D 1/2" Coil Double Support

I need four sets of coil balances for tilt out aluminum windows pictures are attached. The writing on the inside of the white plastic says oh and 137 Patton pending.

I would like to purchase 2 sets of replacements for both sides of the window. I can't figure out the correct weight to buy I also can't figure out how to get the old parts out and the new ones in, Can you give directions for that? Thanks, Rick

don't know what make window this is but the bottom sash can tilt and the top sash goes only up and down very frustrated

I have a Simonton single hung, dual pane, vinyl windows that needs a new balance on one side. Per my warranty paperwork, I believe the window is the Dimensions II model, circa 1996. From the broken parts, it looks to be a triple spring type, and the [barely] visible markings on the spring next to ... (cont.)

Hi can u tell me what is the correct dual or double coil balance support for the 15-177 shoe? The one shown in my pics doesn't seem to fit correctly. I need a double coil balance support for the pictures of the coils and shoe that I sent.

Which dual coil balance support goes with the coil shoe 15-177. I ordered the 1/2 inch dual support and the 3/8 inch dual support but I don't think either are correct.

This is a picture of the coil balance cover that I need. I looked at the covers that you have but I don't see any that have 2 holes for the screws and I need 2 holes. It's for a half inch dual coil. The dimensions of this plastic cover are 4 inches top to bottom and about 1 & 1/8 wide. Thanks for a ... (cont.)

We bought these in 2009. On 3 windows the plastic parts on the side tracks are broken. The part number is 801020. On one window, the horizontal channel on the top of the lower window is broken, but we may be able to repair it.

I have Double Hung windows that are from the year 2000 They were manufactured by Corning. Need Balances, Pivot Lock Shoes and T slot offset hollow seals. I have both Single & Double Spring Balances but I have no Weight Identification.

Lumines 400

I ordered 15-150D they are wrong. Monton window 0003301057. Manufactured 3/30/00

Depth is 0.5 in, width 1.25 in, high 3.5 in

Have 20 year old single hung windows. One window is hard to open and close with a broken part under the coil covers on one side. Want to get all new parts for that one side but not sure what part numbers are. hope the attach pictures will help.

Need information on balance assemblies for Simington Single Hung windows. I have included a couple of photos of the assemblies. The springs are 1/2" wide and there are 2 springs per balance assembly. The lower parts of the assemblies are OK but the springs and upper portion of the assemblies are b ... (cont.)

Need help from bring his part

My windows are Simonton windows. They're single hung. They're white. Some of the parts are broken on the windows. I called the company and they said they no longer make these windows and referred me to you as a place that might have the parts. First two pics...0779 & 0780...are the same piece. Th ... (cont.)

I need coil spring balancer parts for my norandex windows, as it looks like there are 2 coil springs on each side of the window. I will also need to find some of the locking guides that the window pivots on along with the metal pivot arms that are fastened on the bottom of each window that fits int ... (cont.)

Hi I am attempting to repair some windows from 1994 that are still in good condition. However, the coil spring balance systems are broken and need to be replaced. I have attached photos for your review of some of the parts. Could you please help me identify them and let me know if you have those re ... (cont.)

Good Morning We are searching for a brake shoe with the corresponding balancer for it. the weight of the sash is 30 pounds I have attached a photo of the brake shoe do you have in stock?

Weight of bottom sash is approx. 25 lbs and the coil looks to have a marking of 35 on it.