Viewing all customer Discussions for:

75-004 Wire Charging Tool for Non-tilt Windows

Hello, We are replacing the spiral tube windows balances for vintage windows measuring 5/8" diameters and 31" tubes. They are the old vintage ones. Do the updated spiral tubes work in lieu of the vintage ones?

Stanley part # 10-8231-RH two screws on top and bottom 5.25" apart. The gear pivot came loose but I don't have room to press it back in. Looks like I need replace. Do you have this part and can you direct me to installation video? Thanks

recently I purchased from you part number 39?017, the Pan Am/ Daryl window crank. My window is 83 years old, and unfortunately the arm of the crank is not held on with a nut and bolt, but with the mechanism that I have included in the attached pictures. I have scoured the Internet and cannot find ... (cont.)

I have 2 windows that need all 4 balances replaced. I know they are 29" by 3/8" red balances. But I can't tell what kind of foot they need. Can you tell from these photos? They are aluminum non-tilt windows, likely made in the 70s.

Can you tell me how to remove the spiral balances in this window? It is easy to see how to detach the top of the spiral balance. (see picture of top spiral balance connection) But there are no "screwed on" brackets at the bottom of the window which hold the bottom of the spiral balance. (see picture ... (cont.)

Based on what I can see it looks like our single hung window with your 17-052 #63 type of bottom sash clips. The spiral balances are not connected, dropped down in the track loose. If I follow your directions "while someone holds the sash in the open position, spin the spiral up to the bottom of the ... (cont.)

I could use your help in determining the correct parts to buy and I've attached three photos that I hope are helpful.I have a 45" wide double glazed non-removable aluminum double hung window. The half that slides up and down/ opens is 23" high (x 45" wide) and the spiral spring clips at the bottom ... (cont.)

Hi, I need to replaced window balances from 3 different windows. This house is a rental in a different state from where I live. I asked a handyman to take one off and take a picture. Not so good. Is it possible with this pic to identify the part. Its 30" length.

Single hung window. 3/8 dia. Can you determine what replacement i need?

steel tubes on inner side that control window, closing and opening

Where do I buy tension ballast tool for aluminum windows? Where do I buy new ballast covers for aluminum window?

This is a (1936) wood double hung window. The coil is 3/8" and the channel in the sash appears to be 1/2". Would a series 400 spiral balance work? (The description says for aluminum windows). With a #32 bracket? And could you please tell me how to measure the length for the replacement. Do I ne ... (cont.)

18" 3/8 spiral tube 1/2" hole to hole 2 1/4 rod extension 20 1/2 rod length

Here are three pictures of the balance for my aluminum windows . 3/8 diameter tube , 29 in. Length (SPIRAL TYPE) . Can you send me part no. Price and available.Thanks Dennis

I need (2) 17" Spiral Balance 9/16? wide. From the tip to the end about 2? Your foot # 15-009 looks to match my photo.

I'm replacing balances on windows installed in the early 1970s. They are 5/8" diameter and the tube is 20" long. The choices I have are red and blue for the tip, but it looks clear/white to me. Is there a white tip choice for the S500-20?

28 3/4? long (steel to steel) x 3/8? x 3/8? markings say 288 then a small 5. Spring and pulleys system.

9/16? tube, 29? long, 31/4? bracket, 14lb window. Need 2 balances. 2 brackets.

I need to replace the balances shown in the attached picture. The rod is 30.5 by 3/8?. There is no color tip. Do I by the the 400 series? If so the 30? or the 31?. What color tip as there was no tip on the ones that I removed. Thank you, Debbie

Refinishing and refurbishing 50 yr old wooden double hung windows (I'm guessing non-tilt) and the spiral balances are broken all the top parts and some of the bottom. Please advise how to find replacement parts. I measured 21" long (tube) and diameter of 5/8" (though it looks like 6/8" to me if it ... (cont.)