Viewing all customer Discussions for:

75-005 Spiral Balance Charging Tool for Non-tilt Windows

This is what I know about the original parts.....they appear to be the 400 series with the 3/8"diameter, 26" long and the window itself weighs around 26 pounds. The clips are like the # 13 ones on your webpage. It's interesting how they mounted the # 13 clips to a 1/4" thick removable nylon "gli ... (cont.)

There are a total of 8 spiral balances that are broken. I'm not sure they are the proper weight support or not.

A client of mine has General Aluminum no tilt out windows in their town home in Colorado. One of the windows has a damaged spring balance and missing the bottom clip. I need help identifying the bottom clip to purchase. I have included photos of the good balance clip as well as the channel with the ... (cont.)

I have 12 non-tilting vertical sliding windows. All the same height. 10 are the same width and 2 are a bit wider, but mechanically the same design. I'm not certain what series these are for replacing the spiral cartridge nor how to remove properly for identification. I've seen your video where you ... (cont.)

Hello, I purchased 20 springs (S400-34) and 20 brackets (17-043) a few weeks ago and am now trying to install them. Unfortunately, the brackets are not compatible with the springs. The picture of the bracket shows several measurements... but didn't show the measurement of the depth of the throa ... (cont.)

Hello, Trying to find replacement for several 25"long, 3/8" diameter with mounting clips window balances. The track is 3/4" deep and 1" wide. Attached are photos. Thanks

I need to repair multiple windows like this. The spiral has fallen down. Not sure if I need a new cylinder. It appears that all i need is the bottom piece, but I'm not sure and not sure how to "recharge" the spring.

This is for an aluminum window. This piece goes in on the bottom of the window corner to hold the balance in place. It looks like the end of the balance clips in there and it keep the balance in place and from falling out of the window frame. It has a white plastic piece that it seems goes around it ... (cont.)

I work at a mid century modern house that is a bed and breakfast. The house was built in 1948 and has Alwintite windows throughout. I am looking to replace some of the sash springs. I attached a couple of pictures of one I removed because it came out through the bottom of the sash. Since I ... (cont.)

Hinge is a L shape and is mounted on bottom Also see the tension Foot . I need hinge and foot

I've attached two photos. One is two small holes that are located around my aluminum glazing strips -I understand that there is a tool that is inserted into these holes to pop out the clips holding the glazing strip in place. The other is of a part located at the top of a spiral balance. The screw ... (cont.)

I purchased four sets of replacement window sashes many years ago and installed them with Quaker replacement window channels. They worked fine for awhile but are no longer holding the windows open. I want to install window balances but do not know which ones to use. I don't know the make of the wind ... (cont.)

Can you help me identify the parts needed? Swivel balance, etc.

HI, I HAVE OLD ALUMINIUM WINDOWS THAT NEED LOVING CARES. AND I NEED TO REPLACE 6 SPIRAL BALANCES. THEY ALL HAVE 1/2 IN. IN DIAMETER - ( 4 ARE 23 IN. LONG ) - ( 2 ARE 11 IN. LONG, +/- FOR THOSE 2 THEY ARE STILL IN THE WINDOW) I ATTACHED PHOTOS OF THE SPIRAL BALANCE AND IT’S ATTACHEMENT FITTING, ... (cont.)

I have Alenco single hung windows in a home that was built in 1979. Some of the windows need various parts replaced but I need to be able to remove the broken parts to be able to send you pictures. To do this, I need to be able to remove the lower sash and cannot see how to do this. There are no ... (cont.)

I would like to know what is the tool I use to remove and charge a balancer for I think non tilt windows. What is a difference between tilt and non tilt windows?

I need to replace an old spiral balance for a non-tilt window. It is 5/8 in diameter. The tube length is 17". When the spring is fully inserted into the tube it protrudes 1-3/4". I am told this is and extended rod. Do you have this type of rod available? The nylon bushing is white. Could I substitut ... (cont.)

Replacing a 25 " spiral tilt window balance , black tip ...what do you recommend

The old mechanism didn't work, and I can't find a replacement. I need help with what kind to buy from you.The sash is 31 1/2 inches tall, the channels are 5/8 " wide and 3/4" deep. It weighs 10 pounds. The sash is shown in place and removed.

Single Hung NON-tilt window. Balance on either side broken, or the catch to hold the balance in place is broken. the window will not stay up when opened. Do you have repair/replacement parts?