Viewing all customer Discussions for:

S380-29 29" Series 380 Channel Balance

Have 2 separate window balance springs need to be replaced, 2 windows with the same markings and the other a different one. Markings are on one is 26D and the other 28C no other markings.

I have removed both block and tackle balances and I can find no stamps for load ratings. How do I specify that when ordering replacements from Swisco?

I need to replace the channel balances in two sash type sliding windows. It's 29 inches long. Can you help me?

I live in Lake Mary, Florida, and am in need of window balancer replacement for a number of my windows. Below you will see photos of a typical window and the balancer type. We have had ongoing problems with these balancers as they snap the plastic parts. Do you stock this type of replacement bala ... (cont.)

I have Unique 28-C-30 and see that your S380-29 matches the length and top 19-005 attached. As you can see in the picture attached the bottom fitting appears to be different. A previous post indicated option 2830 was needed. Is this what I need for the bottom? If so, is it attached before shippi ... (cont.)

I need to replace 8 Gapco 2330 balances. I've attached images of the guide and shoe, can you advise which balances I would need to order?

Window from Florida Extruders international. UB 28C stamped on balance. Need to know Part Number to order. Also the top plastic piece on window held by 2 screws broke.

Hello sorry I need help identifying the following balance. I'm going to need roughly 6-8, just not 100% which series it is looks like 385 but not sure There are little side wings on the bottom piece as well. Thank you and hopefully someone will be able to help me out, 9/16 width, 29" long balances. ... (cont.)

I'm not sure what kind of window balance im lookong for. Its 29inch length and 1/2 inch width and a mark that said 28C

Will call morning of 7/31/15 to purchase 14 of these.

Attached are photos of my spring balance. Wanted to make sure that I am ordering the correct parts for my windows.

Do you have an S380-29 with a balance shoe that is 7/8" deep instead of 1".

I'm not sure which balance I need for a Caldwell 28 4 CO. I think it would be 19-005 top, but not sure on the shoe. Maybe 15-005? so Series 380? Please see included photos. It is for 29" length and 1/2" width.

I have a window channel balance that has the following stamped on the Channel, UB 28 D. The unit measures 29 inches long and is 5/16 wide. I am not sure what top and bottom styles to order. I have enclosed a photo of each for your review. The window is non tilting and has impact resistant glass. I w ... (cont.)

I have the channel out but can not find any marking . it appears to be a series 380 with 15-005 shoe and 19-005 top 29" long but how do I know witch option to add for weight?? 2810 2820 2830 2840 I have no idea. please help. Thank you Russ

See attachments. The windows are Florida Extruders International, series 1000, installed about 1999. Stamped on the side is LINTOUE 28-0-30, the best I can make out. From metal tip to metal tip it measures 29 1/16 inches

I can't seem to find a stamp on this balance that matches any of the numbers in the options. The numbers and letters I do see are 28D USB.

The S380-29 looks to be the sash i need my window wieghs 30LBS i think the option 2850 will work what part# should i use. Don

My channels have UB 28F stamped on them. Can u identify the weight from these numbers. Windows are milestone single hung 1000 from Florida extenders int. 4'-5" x 60" Thanks

My house, built in 2004, has milestone single hung series 1000 windows. The windows are difficult to slide up and down and with several of them if I open them I cannot get them all the way closed. It appears I need to replace the channel balances. After reading one post, it looks like I can use your ... (cont.)