Viewing all customer Discussions for:

15-194 1" T-Lock Balance Shoe, Closed Cam

I have attached a photo of the balances in my windows. One has broke and many have so much tension that they will pop out next time I try to open the window. Do you have the replacement balance available?

I have a block and tackle sash balance for a tilt window. The code on the existing balance is 28E BSIAO. The balance shoe looks like a SWISCO 15-194. Do you carry a replacement balance? The hook goes into a round hole. I'll need two, if they can be made with the 15-194 shoe

Please see the attached photos of the balance that I need to replace. I only need two at this point. And my balance attaches with a hook instead of a screw. But the hole is round. Does that mean I can't use the screw plug?

These were broken from the balance. They appear to be 3/8 inches thick. I ordered some but they were 1/2 inches and did not clip into the balance.

Need 2 replacement cam that slide into metal slide are to open and close the window.

Hello, I am looking for replacement channel balances which I think I have figured out from your site. The markings on the broken channel are 34B per the photo. The channel measures about 1/2 inch wide and the T-lock is 1 inch wide. This also has the balance clip per the photo. I would need six of th ... (cont.)

looking for a channel balance with # 26C RC RSI. This is what's on the Channel Also looking for the pivot shoe that goes with it. I've seen one on your website that looks like part # 15-194 just not sure if its 1" or 1 1/4". it looks like the 1". Please provide the part# so I could place it on o ... (cont.)

The small plastic "claws" at the tip of the shoe have broken off so they cannot attach to the spring mechanism. Need replacement parts. These are Jeld Wen double hung vinyl windows - 2005 vintage

Looking for a replacement for the balances in the attached photos. Stamp reads 26 B

These pictures are from the window balance of my fiberglass Pella window purchased in 2008. It is from the bottom window. The pivot shoe at the bottom of the balance broke. The pella part number is 22BBI (or maybe 1) with small letters following VA. I need the right and left balances from the bot ... (cont.)

Hi guys! Looking to see if you have an exact replacement for my 20 D BSI inverted block and tackle balance, the bottom part number is 4610108 for the cam portion!

Below are pictures and descriptions of my window balances. The plastic parts / pulleys have become brittle and are breaking. I hope with this information you can help me with replacements. I have 6 windows, (12 balances), that I want to go ahead and replace at this time that are all the same as d ... (cont.)

Hello, we have some Jeld wen windows , series 9980/9980p, h-r20-48x77 / h-r25-44x60 The balancing springs are very noisy and likely need replaced. Is there something else I can do to quiet it down first or replacement better? Balance is 28" long for the metal part covering the spring. I have had ... (cont.)

Hello I need to order a 28" Series 795 balance with a stamp option of 28C. My windows have a hook and a round hole, not square so I need the hook on them. Also I need the 15-194 1" T-Lock Balance shoe, closed cam for these. so I need 10 S795-28 for stamp Option of 28C with a hook on them nbot th ... (cont.)

Hello, I bought S795-34 - 34" Series 795 block and tackle balances but ordered the wrong shoes. The shoe we are replacing is 1" wide x 2" tall. Please see photos for sample. I think these shoes in the photo had a black cam

We have double hung vinyl, tilt out windows installed by the previous owners in 2004.The only number we were able to find was NAMI NFRC 100/200. We haven't been able to raise one of the lower set of windows. We removed both of the sashes and found that the balance plastic piece used to attach the sp ... (cont.)

Hello,we need 4 channel balances. The windows are 17 years old. Hope you can help as we are in the process of selling our house and I don't want to leave them like that. Thanks in advance.

My window is a Series 810 Tilt Single hung dual panes made by Phillips. It is my understanding they went out of business in 2009.I saw no markings on the metal balancer, the metal balancer is 30 inches long.Please advise if you can help or if you need more info.Thank youMark

As you can see I need this size with the top clip and green shoes 1 inch. looking at 34 total this size and 2 more would be 34b bsi I know we could use the s795 but then we would have to make screw holes in all the windows

I need two 795 Series balances with a hook mount top and a 15-194 shoe. The stamp looks like a 36C BSI