Viewing all customer Discussions for:

S385-28 28" Series 385 Channel Balance

Looking to replace the existing top sash guides on several windows where this part is broken. The photos show one that is not broken. Also, I noticed that there are no screws holding the guide in place, just a tab that was molded from the window frame itself. Can you suggest an effective technique t ... (cont.)

26 4 dr caldwell. this is the only marking on the part i have. thank for your help. joe.

I am looking for the replacement for 28" 27 3 TN CALDWELL Please advise the option to select. Thank you.

I'm trying to find a replacement channel balance used in an Alpine window. Printed on the balance is 27 4 CALDWELL BM. The metal piece looks to be 28 inches long. Any ideas?

27HP38-40 D8A CMC 6

Hi, I have determined that we need to replace some of our channel balances with the S385-28" model. I also have a broken piece that screws into the top of sash that I think is called a Top Sash Guide. Pictures of a non-broken one in a window and of the broken one are attached. Is the 18-174 the c ... (cont.)

Window balance for 25 year old Atrium wood windows

Hi! I need balances for 5 windows. My measurement for the width for the balances is 5/8. The balance is 28 inches. The window pane is 34 inches x 29 inches. I attaching a picture of a patio door handle also. Please let me know what to order. Thank You!

old aluminum windows 34*31 Channel balance see pic 1/2 I assume metal is what is measured for the length 29 ? Number inside on metal pic 3 S8 3 11 ? Please advise on which Channel balance ( complete set ) I have to order from you Cant upload pictures ..??

Need 4 channel balance and 10 plastic part connected to window

It feels like something is obstructing it which leaves a 1" gap at the bottom. Works all the way up just doesn't go down all the way. Can't find anything blocking the channels.

Bought a new house. Windows dont work well. Found out balance springs were replaced with wrong tensions (or that is at least what nice Home Depot employee told me)....BUT I dont know what to replace them with. Also impossible to find out here unless I go to "specialty" glass store... So here a ... (cont.)

I have balances that say 18-19" and a stamp on one that says 1840. Do you have these and what in the order info I would need?

Hi, The stamp on the rail is 27 5 AX CMC. Please let me know if you can figure out the replacement part. Thank you Seth

Hi, I need 2 window balances for a window. The code it has is the: 2630 B.S.I mb. Where can I buy it? The window's brand is ALENCO. Thanks, M-

hello my balance is stamped 24-b thats all it says anywhere. it measures 25" long not including tips 26.5" with end tips and its 9/16 wide, if that measurement doesnt exsist than its 1/2" wide. the windows are 70s or 80s aluminum windows and one of the handles reads vista view, if thats any help. th ... (cont.)

Please see posted pictures. I measure the ones I removed, and they are 28" in length and 1/2" wide. Could you please give me the correct replacement part number.Weight of the sash 19 lbs. Note: There is also a stamped letters and numbers on the old piece "b.s.i." and "27 C" Thanks, Chris ... (cont.)

Window were made by Pacific Windows and installed in 2003. The steel channel measures 28" long and is stamped BSI 27 4 00. Window weight is 26 lbs. Thanks, Dave

Hello! We are replacing the channel balances for 2 windows (one is 25 in and one is 28 inch channel balance). By looking at the pictures on line I think they are 380 series (please correct me if I am wrong). I took the sliding windows off and weight the window as well. The smaller windows is 24 ... (cont.)

Have ES windows ES1000 impact windows...need balances for 2 of them . 28" 2721DS