Viewing all customer Discussions for:

S385-34 34" Series 385 Channel Balance

These balance channels are from a CWS Model #3500 single hung window. The channels not including the plastic ends are 34" long x 9/16 deep x 9/16 wide. Let me know if you need more pictures and or descriptions. Thank You.

Hi. Need part number for no-tilt window channel balance. It has an imprinted label that says 3350 BE B.S.I. Its depth is 5/8" and length is 34". I need two of them for both sides of the window. Please see pictures attached for further information. Can you kindly help?Ali

Channel is 9/16 wide and 34" long. End of channel to end of channel. It is stamped with 3390 33. It comes from a Jeldwin window Vertical sash only, no tilt. Please give me a price for 3 sash balance sets. I need to replace on 3 windows.

Balance springs for single hung window .5" x 34"

Hello, I tried to identify my channel balances for non tilt window but nothing written on my old channel balances, the length I measure only the metal part is around 34". Attached is the pictures hope will help to identify the part. Please let me know if you need more information from me.Thank you.B ... (cont.)

My son purchased a townhome that's in need of new window balances. The bottom balance plastic ends have been virtually destroyed. I managed to salvage part of what appears to be the bottom of the balance.A number stamped on the back of the balance is 33400 with "B.S.I." stamped next to the number. ... (cont.)

Metal length 34inch Please give me series part, thanks. Pinglee

Hi. I have single hung vinyl windows. When I try to take out the sash I pull out the takeout clips and raise the sash. When I get to the take out clips I feel the clips engage. As I raise it more, the clips on both sides always either break or get bent and pulled out of the slots. I replaced the tak ... (cont.)

printed on one channel is "33 4 AX CMC 7" channel length= 34" channel height= 5/8"

Need a window channel..can see to find any

i have a maritech 310 series single hung vinyl window that i need channel balances for stamp says 3330 and its 34"

I am looking to purchase 4 of the S385-34 balances for a 40lb window.

I have a window that weighs 43lbs someone put the wrong balancers in it so I have nothing to show you. The ones that are in there are 34 inches long not counting the inserts numbers are 3350 the're not strong enough to hold the window up. The window height is the same as the other window ... (cont.)

I'm looking for (2) window balances like this. Measured 34" without the plastic end pieces.

The attached photos show a damaged balancer for my single hung non-tilting window. The balancer metal length is 34 inches, the cross section is approximately 9/16 x 5/8. The window size is a 4'5"x6'0" window manufactured by Flesher Windows, which is now part of Eastern Architectural Systems. The ... (cont.)

if you purchase a channel balance that supports more weight than the window, does this = an easier open? it'll slide easier? some of our balances are 'sticky' to open and do not slide smoothly. or is this just a sign of the balances shelf life?

Hi, I am trying to see what part number I need to purchase to get the correct replacement. I was only able to find 33 length.

Hi. I'm purchasing the 34" SERIES 385 CHANNEL BALANCE and I'm not sure which stamp option to go with. The sash weighs 27.6 lbs so not sure if I should go with the 3340 (23 to 28 lbs) or 3350 (28 to 32 lbs). Appreciate your recommendation. Thanks, brett

I need 2 different lengths and weight tolerances. The first ones are1/2 in wide and 34 inches long with wings and have 33 3 CO Caldwell printed on the side. The second ones are the same width with wings and are 28 inches by 1/2 inches and have 27 4 FP Caldwell printed on them. I tried but can't f ... (cont.)

The metal to metal length is 34", it is a series 385. The weight of my window is 40lbs.