Viewing all customer Discussions for:

33-090 #8 x 3/4" Philips Pan Head SS Screw

This is attached to a 1/2X1/2 channel balance. The channel measures 13.3/8. The markings on the balance are 14B DG5 CMC 51

Hi.Looking to buy 2 of these. They are 33" long. Not sure of what to order. I typed in the part number 33b bsi on your site and it took me to the plastic part at the bottom that slides in...Yes... Will order them as well. But need the entire metal spring unit.Thank you,Rob

I am looking for the shoe that would fit this window balance.

I'm interested in getting window sash locks for my Lawson windows 18-192, SH 7500 aluminum single hung windows. They did not come with any locks. Can locks be installed into aluminum window frames without breaking the glass? I came across your window sash lock part 90-005 and your #8 x 3/8" so pan h ... (cont.)

hi, Looking for replacement parts in picture. I think the mfg. of the windows was Vinyl Tech. Thanks Jim

Two plastic pieces that fit into a groove in the window frame of vinyl sliding windows to hold the screen in place.

I have spiral tilt windows looking to change pile weather stripping, white preferably. Do I need to be exact; can I be off by a 32nd on the base? Pictures are attached. Also the top tilt latch screws are stripped; what can I put in screw holes to remedy?

We are looking for the right part for the old-style window that is already installed at our place. We do not know the part name/number. Some windows open right side and some left side. once we know the right item we can place the order for both left and right opening. Looking forward to hearing f ... (cont.)

I would like to add a secondary lock to an old slide glass patio door (see picture). Would Secondary Patio Door Lock, Wingless (82-051) be viable for this door in conjunction with the 82-054 Secondary Patio Door Lock Limiter? As this would not be a replacement, are appropriate fasteners and any oth ... (cont.)

I purchased a home that has original MW Twinseal single hung windows throughout from 2000. Almost all of them have broken window balances. I have measured the silver tube (27" x 3/8" diameter)and the black foot (1 1/4"). After studying your website and comments, etc. I think I need the 850 series ... (cont.)

I recently order replacement parts from you. Unfortunately I need something with a larger screw. The holes in the door require a larger screw than the ones I received. I'm sorry but I couldn't find my original order email. Thank you. Alice

I am not proficient using digital devices and appreciate your patience. I have double hung windows and many need parts replaced. Someone I spoke to earlier said to weigh the window. It weighs 14 lbs. We built our house about 15 years ago if that helps. I would so appreciate any assistance you can ... (cont.)

We have purchased from you before. Please see the photos attached. Need your help in identifying these parts. Stamp in frame is 27C ID5 CMC 54 channel length 27" channel width and height is 9/16" Plastic piece 1 7/32" wide, 17/32" deep and 1 1/4" tall. And quote $ for 4 pieces.

I"m looking for the plastic pieces in the attached photos that the spring/string attaches to. These are in vinyl, single-hung "WM" windows that were installed when my condo was built ~18 years ago. I haven't been able to find any other markings on the windows themselves, other than the "WM" logo o ... (cont.)

I need to replace the spring loaded clips the hold the sash in place. That allow the sash to tilt for cleaning. Vinyl Tech windows. Manufactured 11/14/01 I attached the label from the window.

All information is included in the photos

I have reproduced part of my first message to your firm below.It is very difficult for me to remove the window again without parts to make the repair (I am a senior). The pictures and the description will hopefully make identification possible. I am surprised to learn that you do not recognize Stane ... (cont.)

Hinge for Mastic windows most likely produce in 1998/1999 need replacing, as the hinge broke. Could you help me locate the correct part.

Need 4 new sash release levers. The photo shows a broken one marked "Traco", with the broken portion that engages the sash release mechanism remaining visible in the top rail. Our levers resemble your DACO finger lever #26-007 in dimension and shape, however the portion that engages the sash releas ... (cont.)

balancer has 34B stamped on it. Cannot locate similar balancer with the hook style up top. I believe your 795 series is the closest I can find. Any help would be greatly appreciated. I need to order 2.