Viewing all customer Discussions for:

Door & Window

I have a bunch of white aluminum awning windows that use plastic torque bar bearings, that need replacing. I did not see any on your website that matched mine, wondered if you had any other sources. I have made a couple in the past but really need about 34 of them as all the windows need updating. ... (cont.)

The original hardware on our house was installed around 1955-1956. I have a sliding glass door handle that has a broken plastic lever, so can no longer lock. 4 images are attached. There is no manufacturer's name. However, it shows it was manufactured under patents 2,710,156 and 2,701,157. A Go ... (cont.)

Hi, I believe the windows are original to the condo built in 1973. I need to source these rollers - one in each corner of the sliding portion. They're all the same, just positioned differently. The length is 1-1/8", width 13/32", and height including roller guard is 15/32". There is a screw hole wit ... (cont.)

I have the 38-144 lock and then the secondary one on top. How do these work without the little pin that goes into the bar that connects them? Do I just have to replace both locks with one of these, so they work independently, and not use the bar? Thanks!

I need new parts for my window to help with the channel balances. I've attached photos to help identify the window parts I need.

Good Morning. I have circa 1993 Malta Wood DH windows and the window sashes won't stay up on their own any longer when I open the windows. I assume that the balancer is worn out so I took apart the vinyl jamb liner to get to the balancer. I've attached photos of the assembly as well as close ups ... (cont.)

There are no numbers or names on the door or lock

My Patio door closes just fine and the alignment "seems" good, but it must not be because the latch bumps the keeper when I try to close the latch. Then it doesn't fully extend and latch. The workaround is to start with the latch extended and down, (lever halfway) and finish it off after closing. Gu ... (cont.)

Hi this is Tyler with Exline inc. in Salina, KS and I am working on a door and need to start a post to see if I can get help on the part I need. Attached is some pictures. I believe I found the correct hardware but would like to double check. The door is flush on the outside frame and the hinges are ... (cont.)

I looked at the glazing parts list but they all have a edge at the top mine is round did i miss somethig

Hello, I recently purchased a home built in 1966 with a room addition in the 70s. I have many windows where the snap in glazing is damaged. Attached are some photos both on and off the windows. Please help identify a suitable replacement. The part is 1/2" wide, 5/16" tall, with a 1/16" lip. ... (cont.)

We are looking for this same lock on sliding glass door to replace. A second email will arrive with 2 more photos. Suggestions are 82-225, 82-214 and 82-211 but none of these seem to be same dimensions. Have other suggestions? Thank you. Andrea B

I need 80 pieces but before I place an order, is there any chance that I could buy just one to see if it actually fits?

I need a couple new block and tackle channel balances. Not up on my window lingo, but the windows tilt in to be removed and both the upper and lower windows move up and down. The balance is 28 inches long and is stamped 2730 BF. The pivot bar for the window also has a 2369 stamped on it. ... (cont.)

I am looking for replacements parts for a single double-hung window. I closed the window the other night and I heard a snap...The window will no longer stay open on its own. After research, I discovered the company I purchased the windows from 13 years ago is out of business and apparently my warr ... (cont.)

Window balance length is 29" Stamp reads 28C USB Last attached image is a sticker from the window Milestone single hung series 1000

The Truth arm operator work on all my windows, but handles on 3 of the 5 windows spin. The handle is made by weathershield in Medford Wisc. and it does not have a set screw on the bottom. Do you have this handle? Thank you, Mike F

I'm trying to figure out what channel balance I need. The length of the metal channel is 25 and 3/4 inches. The only thing I can find stamped on it are the numbers 25 2. It also says BSI. It looks like product code S385-25. I don't know how to tell the sash weight range I need or if this produc ... (cont.)

Hi I am in need of new pivot pins and shoes, but i can not find any identifying marks on the window. i can't find what brand the window is any help where to look would be helpful. Can i still buy pivots with just measurements? the so much

I need to get two of the left side window cranks that are pictured. I see several on your site and not sure which one to order. I also need two of the screws pictured if you stock them. Please send part numbers if you can identify them.