Viewing all customer Discussions for:

16-002 Take Out Clip

Hi, I need the "clips" (first picture)...that hold the spring mechanism in the windows on the side. Third picture is a bar/spring that has popped up due to an old broken clip.

I need the small metal clip that fits into the window frame upper that the balance stops against.

I just ordered 10 valances from your company. One of my windows does not have the top clips in them to hold the balances in as they're put onto the window? Do you know what this part number is? Also I need the replacement clips for the sides of the windows to hold the balances in place when I am rem ... (cont.)

here are the things i need to fix my windows. when i was looking at the ones you guys suggested it had several different options like 2610, 2650 based on weight. Im not sure which one i would need

Existing channel balance is stamped 28E but the length of the metal part is just under 29" (28 15/16?). Top and Bottom attachments both have flanges. Width of channel is 5/8" and depth is 1/2". Do I need take out clips? These balances are for a window in a condo I recently purchased. HOA has b ... (cont.)

I have one bad sash balance and would like to replace both. Window ID is LIN 1194 U32-HVS as shown in picture. I've uploaded a picture of the bad sash balance (the spring from it is missing) and a picture of what I believe the sash balance should look like. The length of the metal channel alone is 2 ... (cont.)

The balance spring pictured is 1/2" (9/16") wide and 30" long, not including the plastic fittings. It is stamped with 29 3. I have also included a picture of a release clip that I will need to order. Please let me know which parts to order.

Hello, Hopefully you can help me. I need new balances for 3 different size windows in our home, two for each balance numbers sent. Also the clips that go on top of the windows that grab the balances to remove the window. Lastly if you have them are 4 little plastic parts that snap on to the sides of ... (cont.)

Hi, I need to replace 2 broken channel balances which seems to be custom made as I cannot find them in your catalog. Those channel are used for Traco single hung impact windows (no tilt) Metal channel lenght is 24 in. The top seems to be new security 19-041 Shoe seems to be 15-004 Engraved: 23DS ... (cont.)

Window balance is marked "14D U.S.B." Metal Channel is 15" long, just under 1/2" Wide, 5/8" Deep into pocket in Window frame. I have found an Internet reference for the top end as p/n 60-507, and for the bottom end as p/n 60-503. Note the wings on the sides of the bottom end. The weight of the ... (cont.)

Piece is 23" long. I am also missing the metal piece at the top of the window which tilts out with flat head screwdriver

Hello I'm trying to identify the correct replacement for channel balance on a non-tilt vertical slide window. The metal is 1/2 inch wide and measures 26 inches and 11/16 to be exact. As the image shows, the marking on the metal says "26 9" I tried looking for the replacement on the site but did not ... (cont.)

could you please help find which is a right channel balance for my home. I measured the old one (broken): channel balance shoe deep 7/8" (15-029?). The top looks like 19-005. The channel width is 1/2", the length 28". I need purchase 3 channel balance and 1 clip 16-002

I have photo of parts on my email I tried to forward photo email to www.swisco.com from my yahoo email. Yahoo said check the email address

my window balance are no good anymore don't even think about holding the window up or snug in place. so need to replace them 2 per window, 4 windows.probably should replace clips also if I can figure out how to take them out.I have added photos hopefully that helps narrow down what I need. also the ... (cont.)

information printed on channel 23 4 for CALDEELL I need 4 clips And 6 channels

I have the Chanel and it looks ok but I need to attach it to the side but don't have and of the parts for that. What do I need. About 1/2inch Chanel about 12" long

Identifying numbers printed on the unit: 32-3 FA2 CMC 19The metal channel is 33" long, the back of the channel is 1/2" wide, the open side of the channel's slot is 9/16"One side of the window is also missing the little clip that pops out to catch the channel balance so that it can be removed. Fortun ... (cont.)

Need metal piece that fits on the window frame to disengage the window

I have a window(~30yrs old)where the channel balances are completely gone. Information I was able to find: Mfg Code: PS-1; DH-R30 Series 1500/1580/1900/1980 MST 4060 from a label. And 2 40R stamped on the U bracket. U bracket is 1/2" wide and 29" length. Attached photos 1. Bottom end with clip ... (cont.)