Viewing all customer Discussions for:

21-151 5/16" Nylinder

what do I need for bottom of my mirror door

I am looking to replace the tracks, pins, and all other hardware for all the closet doors in the house my wife and I just purchased. The house was built in 1958 and has the original closet doors, and we expect the original mechanisms. I have had a really hard time identifying and finding the parts t ... (cont.)

I was considering replacing my clunky pin assembly as you recommend but the hole for the clamp is not square. Is that a problem? Also, the pivot clamp needs replacing but I don't see an exact match. Photos attached. Thanks!

4"long, small end 1/4 diameter, large end 3/8 diameter. Need 3 of these plus springs& clips.

I recently purchased a rebuild kit for ~1980s mirrored closet doors. I cannot get the pins to stay in the pin caps as the pins pull out when opening/closing the doors. I reversed the spring tension on the doors(top: push up vs pull down to engage pin) and the pins still will not seat in the cap. ... (cont.)

Hello, I have 8 metal bifold doors that are needed to change with the new set of hardware in order to open/close them easily & securely. I am looking for your help for identifying all needed parts of the hardware. There is a tack of the sliding door on the top, and another track on the floor. I ... (cont.)

Metal bifold doors 36" wide by 93" high. Need new track and hardware. I can give more detailed information if you need it.

I am renovating my place and decided to spray paint my old closet doors, unfortunately once I removed the doors the top pivots came off and the little plastic plugs are no longer keep them from springing out. I will need to order new top pivots and bottom pivots along with additional stationary pivo ... (cont.)

Building is built maybe in late 1960? I want to replace all pivot parts at top and bottom.

hello I'd like to refresh tired 50 years old metal bi-folds. Could you help me identify the parts shown in the attached pictures? Pictures are top left, top right, bottom right and left. I'd like to replace top and bottom tracks as well. thank you

Hello I am sending photos of doors that I am to repair... if possible. I would like to see if you could check the pics out and determine if you have the parts... but... mainly... look at the pic where the bottom of the door has damage and whether it is worth repairing or not. This is for an elderly ... (cont.)

It appears that your part numbers 21-001, 21-007, and 21-154 could replace the parts in the attached photographs. I assume the guide pins would also fit the upper and lower door tracks. Could you please confirm all of this before I order? Thank you

I need 2 Bottom Rollers, 1 Bottom Pivot, and 1 Top Roller. I can't find any markings on either the parts or the door. Each is about 4 inches long. Any help you could provide would be greatly appreciated! -Don M

A little job I'm doing for someone that has 3 closets. One 5' wide, one 4' wide and one 149" wide, all 93" tall. Will replace all hardware and track. They have a beat up wooden track that I'll do with maple or some other hardwood. Would you suggest a metal track? I don't know the manufacturer of t ... (cont.)

The pins and parts of the pin assembly are missing on some Weldwood bi-fold metal closet doors in a house we just bought. Can you tell by the photo what I would need? I need 10 of these if you have the correct part(s)? There are photos of the part both installed and removed attached. ... (cont.)

I'm looking for track parts fittings for the doors

I have a FULL-VU closet door composed of two bi-panel elements. To repair it I started to document each element: top pivot 5/16" top glide 1/4" bottom pivot 5/16" bottom glide 1/4" A very wise decision as there appeared to be only simple pins and such. Actually each of the four locations, a ... (cont.)

I need help with parts for this door.

I am trying to fine the correct pins for a Flow Away ,steel ,mirrored ,bi fold closet door. The doors have two different types of pin holders. Most of the doors that work have white plastic bushings at the top an bottom of the steel door with some kind of black plastic for adjusting. These seem f ... (cont.)

pin is steel i/4" diameter, 4 1/2" long including nylon slider cap. Pin has two grooves 1/2" apart around the middle encircling pin is a spring 1 3/4" long, 5/8" in diameter for 1" narrowing to 3/8" at the othe end the spring floats free on the pin in the door channel through which the pi ... (cont.)