Viewing all customer Discussions for:

S385-33 33" Series 385 Channel Balance

I have two similar windows with the same connectors and can you help me find the right part numbers to order? Milgard 26/3/GW/CMC 7 -19 pounds Milgard 26/5/GW CMC 4 - 16 pounds Top looks like 19-005 and shoe looks like 15-005 Thank you,

I want to get the right parts for my windows. I need to replace the mechanisms to four windows. Two of them are 33" number 3240. The another ones are 27" number 26DS 33. I have sent some photos for showing better my request. Could you please say me how I can order the parts. I want to replace everyt ... (cont.)

Hi, I need to replace bunch of series 385 channel balances in my windows. I know the lengths I need, but I want to make sure I order the correct strength for each window. Some (but not all) of my current (broken) balances have some numbers stamped on them, but they do not match the numbers in your ... (cont.)

Window weighs exactly 32 lbs. Should I get the 3250 or 3260 Model (33" Series 385 Channel Balance)

33 inch channel balance 32-4 LX CMC 11 Hello, i am looking for this part. My windows are milgard. Can someone help?

Need a price on 7 sets of balances and ETA if ordered tomorrow to be delivered to 91744 area code

I have Milgard single hung windows. The balance is 33 inches long and has code 32 5 FX CMC 2 stamped on it. I think the correct part is 33 inch Series 385 Option 3250. Does this seem correct to you? When I measure the bottom fitting I get 1 & 2/32 which I think is close enough to 1 & 3/ ... (cont.)

Milgard window. Photo of stamp attached. Which stamp option should I pick?

Hi, I would like to replace these two channel balances but I am not sure model number or option to order. Please help identify the suitable replacement. Thanks, Eric

Milgard metal Windows from 2002. Do you need the weight? The bottom shoe from 'fang tips' to peak of bump is about an inch. Is this the right way to measure what is described as 'deep' on the product pages? Thanks for the help.

Can you help me identify the right part for channel balance replacement. 33 inches 1/2 wide windows weight: 22 pounds

price on 2 sliding window channels with spring. And the shipping cost to Rio Vista, CA. marking on it are 32 4 CV CMC 7. Photo attached.Thank you, Amy

I need to replace the window balances and i have Milguard single hung., Winslow windows (builder grade). The windows were installed in 1997 when house was built. The windows are 36? x60? (27? balance metal channel length) and 36? x 72? ( 32? balance metal channel length). The marking on the 32? s ... (cont.)

The window slides up and down. I believe it's called a channel block and tackle. The length is 33 inches and the width is just over 1/2 inch. The only markings I could find are the following 32 4 EW CMC 4 Thank you for your help.

2002 silvercrest mobile home. Need to replace a few of these but don't want to order the wrong ones. Can you point me in the right direction.

Hello, I'd like to verify this is the correct Channel Balance. I believe it is the 33" series 385. The part is stamped 3290 (see photo) but there is not a 3290 option in your sash weight menu. The sash physically weighs about 37 lbs. please advise. Also, will the Pivot Lock Shoe, 1/2" Thick, Blue Br ... (cont.)

Not sure what your replacement parts would be. I need two of these (for now). The length of the item is (end-2-end on metal frame) 33". It has a marking of "32 4 CADWELL FM" on the one side. The 2nd photo showing the end pulley area has the top most of the 3 plastic pulley's which is worn, so a lot ... (cont.)

Looking for replacement balancer for the above. I have purchased other balancer in the past from you.

The metal part of the balance is 33" long

I need 2 new channel balances there is a part number on them 32 4 cm cmc 10 I'm not sure what to order so I'm sending you photos