Viewing all customer Discussions for:

26-040 Pivot Bar, 3"

I do not have any information on the double pane pivot window; so I am hoping the picture will help to locate the bar I need. Thank you, Frank

Looking for a replacement sash pivot bar to fit your part 15-047. Appropriate size: 3" x 1/4" x 1/8".

replacement pivot bar

Can you tell from the attached photos which pivot shoe I need Thanks Scott

Our mountaintop inn has aluminum spiral balance windows. The shoes are breaking and we can't find their replacements. We have a few shoes that look very much like Swisco's 15-045 and 15-212. However, the 3/8" thickness of those shoes is just a little bit too thick. The windows are too stiff for our ... (cont.)

Swisco, A window on a home purchase was completely missing the ballast system... A second window was of equal dimensions is in the house, I was able to transfer the ballast system to the window of the buyer's preference I am now looking to get all parts to complete the cannibalized window... Dual sp ... (cont.)

Hi- We thought this was the pivot bar, but it doesn't look like your pivot bars. It is the piece that fits into the pivot shoe. Can you help identify so we can replace a broken off one? Thank you! Stacey & Neil

window stash pivot bars that have disintegrated in my windowsI am unable to locate any tags indicating model or series of the window. I can tell you windows were purchased at home depot approx. 2016.do you have any suggestions that I could check that will get a general idea as to model. I need to o ... (cont.)

There are no names or numbers on the bar, nor on the window. I purchased the window about 15 years ago at Lowe's or Home Depot..It is about 2 5/8 inches long with three screw holes.James K

I need a replacement balancer and tilt bar with plastic housing. The bar has sheared due to rust and I?m unable to remove it from the shoe.

L 2 1/2" X W 5/16" X H 3/16" Steve the first hole is 1 3/8" from the long end and the second hole is 2" from the long end

I need to replace 2 1/2 inch long swivels the shoe and the Tilt window latch that you see in the pictures. Can you please help me identify the numbers that I need

Tom I send a picture. Kept looking and found what I need 765 series balance. I need pivot for that balance. Single hung vinyl hung vinyl window/ThanksJim

Photo shows old corroded bar that I drilled out and a newer matching bar from another window. Both are 1/4 wide, 3/16 high, 3 long. Your 26-040 ,26-068 ,26-040 and 26-068 look close but have only one screw hole. Suggestion? Thanks.

Hi,I am hoping to get some help identifying the complete coil balance and sash guide parts for this window. The upper part of the coil balance is 3 1/2" high and 1" wide. We will need the bottom portion as well where the window sash hooks in.Please let me know if you can assist. If there are a few o ... (cont.)

Need part numbers for a pivot bar and I need pivot lock shoe Thanks

Need to send photo of balancer and window slide keeper

Sir, I am looking for a 4 inch long (or longer) pivot bar similar to your model 26-040 which is 3 inches long. I am looking for a longer bar because the receptor grove on the window is in part missing. See the attached photos: 1900- existing pivot bar at left side of window - 3 inches long 1897- rig ... (cont.)

This is Shou again. We like to replace all 3 bottom of porch window both side hardware too. Porch window is heavy then bed room window. Spiral Balance tube diameter is 5/8", length of silver part is 29", rest part is on the picture. Hope we give you enough information. Thank you. ... (cont.)

Hi Have a Silverline single hung window built in 1999 need the pivot pin and it's a "U" shape about 3" long. Can you help? Called Silverline and they were no help, they're asking for a model # of the window which there's no label and also sent then pictures of the window and pivot pin, they sent me ... (cont.)