Viewing all customer Discussions for:

62-108 Tension Cord Clip

One half inch width. 27 5/8 " length of metal part.

It is a Milgard 's non tilt window and The window # H-LC30-48x78 & H-R20-108x78 .The Channel balance length is 27?and The width is 1/2?. The balance stamp on it is 26-4 BSI . please identify what the replacement number for the channel Balance is and let me know so I can order a replacement for repa ... (cont.)

I need a pair of this in 19.5 inch length. As per photo, markings on back say 19 5 BSI T E. The T might be an arrow pointing up, hard to tell. Please advise. Thank you!

at the back on channel balancer say 31 3 my measurement is 32 inch do you have such size off balancer

I am looking for the following 1/2 non tilt window channel replacments for Migard windows. The stamps on each one are as followed 20-4 will need a total of 4 (2 sets) but don't know what part 20-3 will need a total of 4 (2 sets) but don't know what part 20-4 will need one set but dont know wha ... (cont.)

I have this type of balance that I cannot find a shoe for in you're list of items. This channel is 27 inches long without the ends. I need 10 of these plus four more but for a window that weighs 15-20 pounds. Thank you, Tom

Not sure which sash to buy. My single hung windows are 33" by 16.5" and 33" x 26"Most of my photos are from the old sash to the 33" by 26" inch window.Need about 10 each of the 33 x 26" and 6 each of the 33X16.5 inch window. Hopefully you can get the weight of the large window from the inscriptio ... (cont.)

metal measures 32 inches i need one

Existing balance stamped 13 3, along with CJ EP, with BSI in between those letters, running perpendicular. Matches description for your Series 385. Length of metal is 13&5/16". Should I order the 14" stamped 1330 (seems to match my existing 13 3), or the shorter 13" stamped 1230? And getting a p ... (cont.)

Hi, I am looking to replace the balances for 4 Windows. Do you have a part that matches these pictures. I don't have a picture installed. Thank you

Need a replacement for channel beam. Channel beam labeled 2630. PA marking on bottom boot stating PA 6598264. Top boot has no indicators or markings. Length of beam 27 inches

I have two different channel balances (only different in length. The first is 15 long and 1/2 wide. The second is 21 long and 1/2 inch wide. I am not positive on the ends as far as identifying them correctly. I would greatly appreciate your help I am sending pictures. I need two of each. ... (cont.)

I need a two replacement slides that look like this... see photos.

I have 2 balances with a broken piece that fits into a hole in the window frame. Also has a BS td stamped by the numbers. The metal channel is 15 and 21 inches with the same end piece designs. What should I order?

I need a replacement 28 inch window balance for a non-tilt window. The width is 1/2 inch, and the imprint says 27 4. Can you please advise which part I need to order? Thank you

Hello,I am looking for 20 replacement Channel Block and Tackle Window Balances. The manufacturer of the vinyl windows was "INSULATE INDUSTRIES," a company from Auburn, Washington, that no longer exists. Please see attached photos for dimensions and design.WilliamThank you

I need two different items, one of each. The top and bottom attachments are the same for both. One has a channel length of 26 7/8" and markings "26 3 B.S.I PR". The other has a channel length of 29 7/8" and markings "29 4 B.S.I PR".

"22 5" is stamped on the metal portion of the balancer. It is a single hung, non-tilt balancer, 1/2" (actually 9/16")

Need replacement balancer for millard window installed in 2007

Just checking that the 20" Series 385 1930 will work to replace a B.S.I. stamped 19 3 ? Thanks in advance.