Viewing all customer Discussions for:

15-104 Caradco Friction Shoe

The springs are attached to the lower window by a plastic part which broke. Need to replace the springs and plastic parts and the metal attachment to the windowAre there install instructionsGlass interior measurement is 27 5/8exterior width 30 5/8exterior hieght 31 3/4peter

First picture shows pivot shoe side view and pivot shoe installed in vinyl jam. 2nd picture shoes pivot shoe top view and same pivot shoe in vinyl jam. The pivot shoe is 3 and 3/8 inches long, 1/2 inch deep and 7/16 inch wide.

I need shoes and balances

Thanks for your time, I need to see if you can identify the attached parts from the pictures I have attached! We are thinking they were sold in 2002/03 and purchased from M & W.Regards,Tim

I cannot find any make or model in these windows, but the plastic sash support which connects the sash to the spring is broken in most if not all of my windows. The house was built in about 2003, so they are about 15 years old. In the attached pictures, the plastic support on the right is broken, an ... (cont.)

Hello, I have double hung wood window. Plastic Piece (foot?) that connects window to sash balancer spring has broken. Looking for options/path to easiest repair. Photos of (intact) piece attached as well as vinyl jamb that sash balancer spring resides in. No idea on window manufacturer, but house ... (cont.)

This is at the end of the spring assisting the raising and lowering of Windsor double hung Window. This is the upper window but the lower window which does not work is the same Configuration. Need a new plastic piece that has broken

Over the years I've had to replace this part numerous times and I'm about out of it. Do you carry such a part or do you know what I should call it and who might carry it? Thanks!!

I have a Caradco window ("caradco 14" found engraved on metal holding the glass) whose support hardware has broken off. The window frame part of the hardware is shown in the first photo.

Can you see from the pictures what might be needed here?

Hi - I'm trying to find these balancers for 25-year old wood windows. It's a 23.5 inch long spring with plastic clip things on the end. I've attached photos of both ends, length of balance, and the clips. I couldn't find a stamp for the balancers. Thanks in advance for your help. I hope you hav ... (cont.)

MW Windows will not stay up need stick to hold them up. Windows were installed when house was built in the 1995. Wondering if you have parts for these windows they are 53" long from top of spring to bottom of window. Thanks for any help

I need to purchase a few balance shoes for my wooden double-hung windows. I cannot identify the brand of anything on these windows, so sorry about that--no help. But I took pictures of the shoe. One that's still inside the vinyl jambliner and still intact, and one outside the jambliner that has b ... (cont.)

The window is a Norco/Jeld-wen double hung wood window inside and out 2x4 exterior walls with brick veneer. Need the broken part =as shown in attached pic. Measurements of the window sash and glass size below. Jambliner- 73 3/4 inches long (measured from sill to top inside), bottom sash size is 30 ... (cont.)

i have some hurd windows i need to replace the friction shoe on. looks like the 15-104 will work. these are jamb liners you squeeze outward to tilt the window. ho do the jamb liners come out to replace the shoe? your video shows screws to remove but none on these units. thanks

NEED THE WHOLE ASSEMBLY. 30" SPRING. SHOE IS 1/2" WIDE AND 2 1/2 HIGH.

Hello, I need 4 clips identified in the picture. The window itself and the clip have no identifiers. The clip rides at the bottom of a coiled spring and attaches to a metal post on the bottom of the window unit. Thank you for your help David

Good evening. I

Hi, I need to replace several window channel shoes. Over time the tension from the spring has broken the plastic clip on the shoe that attaches to the spring. Neither the windows nor the shoes have any identifying marks on them. This is a photo of a shoe that's still in the window and in use ... (cont.)

Looks the same as you as your Caradco 15-104 except the front face where the adjustment screw is located. My part is only 1/4" wide across the front. All the other dimensions are the same. Can you help?