Viewing all customer Discussions for:

15-150D 1/2" Coil Double Support

The house we recently purchased has two different eras of tilt windows, half from the mid 80's, the other half from the early 20's. The older windows use a spiral balancer system while the newer ones use the metal coil system. (see picture) Is it possible to retrofit the older windows using a newer ... (cont.)

Markings say #5.5 and 35", PAT523208. I believe they're Simonton windows. I'll need to replace coils, shoe and support. Thank you in advance for your advice!

Does not need to be exactly the same. Number on coils are 35" #4.5 and other coil is # 5.5 35"

I have some Trilite windows in my home with broken springs. They have double coil springs that say, "5.5 33" Pat5232208"on them. Could you please help me select the right replacement parts, I need several. Thanks,George

Hello, I would like to order the replacement parts for my window. There was a metal coil inside the pack that broke. I believe that it's an Andersen window.Please let me know if you need any additional information.Thank you,Mike

looking to buy the sliding hardware, the existing coils are broken. it says #7.5 31" PAT523208 on the coild

Looking for window balance ,for simonton windows

Need 10 left and 10 right complete replacement for what I believe what you refer to as a constant force balance system. I have Simonton double hung windows, manufactured 7/11. Part # on existing is 801020. Need exact replacement, including piviot shoe, coil spring and coil spring cover. Believe that ... (cont.)

Two coils; one stamped 7M, the other 4. Width measures 15/32". Need 2 sets for left and right. May get 2 more for another balky window of the same make. No mfr listed. Shoe is reinstalled for now.

Need Left and Right Coil Springs Hardware shown in the pictures for 6 windows. Label picture is from one of the windows.

Part number 801020. Coil says 4.5. 35" p . Coil look to be 1/2 " need shoe too. I will need whole set up for both sides of window right & left.

I was replacing a broken coil with the new one you sent me and I unfortunately broke the plastic end piece that holds the coil. I'd like to buy two of them please. See the photos for the same piece on the other side of the window. It is approximately 4"x1". I might as well get the bottom pieces too ... (cont.)

Trying to ID the upper portion, the tilt shoe, and the spring, or help me determine how to better ID the spring we need for this unit. Thank you...

I order the wrong part for my window this is what the installer says I need. Also can I return the parts I ordered.

I'm a contractor trying to fix a window for customer, but I can't tell what size of coil balances I need. They are the type like your Series 196, but I cannot read anything off of the springs. There are 2 springs, piggy backed on each side, so I need one long and one short. The window is a tilt-in ... (cont.)

Hello,I have attached three (3) photos showing the types of replacement parts I need for a number of my home windows. The windows are 20 years old, and I believe they were made by Simonton.I would like to purchase a number of the plastic covers/holders for the balance springs, and also the correct ... (cont.)

Hi, I am looking to replace a Milgard double hung window balancer. Photo attached. Do you carry this part?

Hello, Attached are pictures of the balance assembly from my BF Rich Dual Hung Window. It weighs 25 lbs. Can you tell what replacement parts I need? Thanks, Rob

It most closely resembles the Certain teed coil balancer by dimensions. The band is 3/4" thick. The pivot shoe is 1-1/4" wide. Over all length looks to be about 4-1/2".

Good Morning, I need to replace a few Simonton double-hung window balancers. The spring section, at top of the window track, has two units, each fastened with two screws, with the lower spring unit slightly longer than the top spring unit. I'd like to obtain the parts to replace the entire balanc ... (cont.)