Viewing all customer Discussions for:

S380-29 29" Series 380 Channel Balance

I have a window channel balance that is marked 28C. The channel measures 9/16" which I believe is the 1/2" channel you sell. The metal part of the balance measures to be 29". It appears to have the 19-005 and 15-005 ends on it. Can you please suggest the stamp that I need?

my channel balance is stamped 28 4 CN Caldwell. I feel that the top piece is 19-005 and the bottom is a 15-005. which would make it a series 380. But when i measure the channel like your diagram, the channel is 29" not the 28 like the stamp says. Which size should i order the 28" or the 29"? Th ... (cont.)

Hello I have a 2006 built home and about 10 windows all have broken balances. I need replacement ones. I removed one of the balances and took pictures of the measurements. The balance measures 29 inches long. There was a sticker on the window. Info on the sticker: Milestone Single Hung Series 10 ... (cont.)

Using the videos, pictures & posts on your site, I am pretty sure I have identified the S380 as the balance I need for my Kinco windows. The measurements for the top & shoe are pretty much exactly what I have. My concern is the the length of the metal is closer to 29 5/8", not 29" or 30". Your ad ... (cont.)

Looking to replace Channel balances for a few windows They all appear to be the same channel parts in terms of channel balance (although the windows are slightly different in width / weight) The existing channels are: 29" Long 1/2" Wide (technically 5/8") The measured depth of the bottom shoe ... (cont.)

What are the weight differences for the following channel balance options for the 380 series: 2810, 2820,2830,2840, and2850. Thank you, Tom

Have some questions on the 380 series 29" length. I have Eleven Harcar windows approx age 24 years. Current balance channels are "hemmed" construction. Yours don't appear to be "hemmed", any problem there? Stamp on side of channel is 29 1 A I. What is the corresponding weight stamp for that mark ... (cont.)

I have several windows with bad balance units. Your 2830 or 2840 units seem to be the best match I can find on your website. Please advise as to your order, postage, and/or return policy. I will probably order 12 units. There isn't any weight stamp on the existing units. The only designation is 28C. ... (cont.)

I need to order replacement balances for three Kinco non-tilt windows. Attached are the pictures of the three different balances along with pictures of the tops and bottoms. Here are the markings of the balances: 24 9 JW CMC 11 28 4 KW CMC 11 29 6 KW CMC 11 Would you please let me know whi ... (cont.)

Hello I need to get the correct part number for my channel balance. The length of the channel is 29", width 1/2". It appears that S380-39 might be correct but the width of the shoe is a little bit shorter than the 1" marked in your photo and I am not sure of the extra code I need. I have includ ... (cont.)

Have 20 Florida Extruder Milestone 1000 single hung windows. Replaced the channel balances in several windows within the first two years under warranty and over the last 4+ years an additional 9 windows are now no longer working. Some of the now broken balances are windows opened rarely and others i ... (cont.)

The stamp on my channel balance does not match. The stamp I have is 28D.

Looking at your website I believe I need the S380-29 channel. I have hurricane proof windows and they are heavy. The stamp on them is 28F. I was wondering if a 28D would equate to the 2840, would the 28F be two steps up to the 2860? Thank You

I have reviewed your non-tilt window balances in shop items. I believe the ones I will be ordering for replacement will be # 380 in 27"; BUT, I have questions. First: the channel on the ones being removed measures 1/2" x 27 1/5" long. Does that equate to the 27" length? Second: the only number ... (cont.)

I have pulled out my balance and the only thing stamped on the side is 28E USB. The window weighs 28 lbs, the S380 29 looks really close, but top and shoe attachments are tough to be sure it they are correct. Measurements are close. Can you provide any insight?

I need at least 8 balance assemblies for windows 52" wide (total opening). The existing balances have 28D stamped on them. What is the equivalent 4 digit code? Also your drawing showed a dimension of 1" where mine measures 15/16" inches. See photo. Any problem? Tom

My shoe is shaped like the 15-004 and 15-005. The only problem is that the size. You show a 1 inch and 1 3/32 inch. Mine is 7/8 inch. Not sure what I need. It is stamped with 28C and is channel is 29" long. The window weighs 20 lbs. Thanks for any help you can provide. Tom

The stamp on this 29" channel balance says 28D. I called a repair shop here in town and they quoted me $55 for the install, etc. but was wondering if it was simple enough to do myself.

From the detailed information on your website, I have determined that I need to order two S380-29 Channel Balances. However, I need help choosing the correct option. There is no stamp on the broken Channel Balance but the following code is printed on the metal: 28 4 FX CMC 11 I have removed the ... (cont.)

I'd like to identify the proper replacement parts for my non-tilt aluminum window built by Florida Extruders in 2003. Enclosed are pix of the proper parts. I'm assuming the spring comes installed in the unit. I've enclosed a few pix...I figure the part number would be S380-29 for the balance, and 18 ... (cont.)