Viewing all customer Discussions for:

39-351 LH 9-5/8" Hinge Arm Assembly, Pella

Cannot find the above part on you parts list.

We have older Pella windows 1976 vintage. The opening mechanism has two rollers at the bottom which should allow the window to be cranked open. The rollers must have worn to the amount that they no longer hold the support shoe to remain clear of the window frame. The support shoe drags on the wind ... (cont.)

The metal piece that attaches to the white plastic teeth is gone on one of the windows. The picture is of a left opening window but it's a right opening window that is broken. Do you have this part?

Year 2000 top hinge bar and bracket. Not the "click" fit

I have ordered part # 39-352 and #39-395 and the part that screws into the window is the wrong size. The size in the picture needs to be 8" and the 10" arm needs to be riveted next to the first screw hole like the picture. Do you have this part?

The support arm bolt broke. I don't believe i need a whole apparatus, but I don't know. Pella is the absolute worst! Any help would be welcome! No model # because they were geniuses and put them on stickers then, which were removed before I bought the house. Window still opens. This is tge tight s ... (cont.)

Good Morning,I am looking to replace the hinge on my pella window. Below are the photos with the measurements and parts that I will need. Please let me know how to proceed.Thank you,Isabella

My home was built in 1979. The hinges on my Pella casement windows consist of two pieces: the slider part and the arm part. They are separate components. The two parts on the bottom hinge, for example, are the roller part (that slides in the track) and the arm which pivots as the window opens. ... (cont.)

I am trying to get replacement parts for my 30+ year old Pella Casement windows. I have attached a picture of the upper and lower Hinge assemblies... I cannot identify serial numbers on the glass...GUARDIAN Webster Mass, ANSI Z 97.1 1975 and other SGCC 300, 16CFR 12012 and others I am sure are not ... (cont.)

Two quick questions 1. LH means from the inside of the house the hinge is on the left side, correct? 2. What is the length of the short side of the 39-351 Pella Hinge Arm. My 1998 era Pella window long side (without slide) is just less than 10" and the short side around 6" (second story window, ... (cont.)

Looking for slide rollers (part name?) for Pella casement windows that are probably 30 years old. The windows are wood with a vinyl clad exterior. This part slides along with top and bottom window sash when you crank the window open. Any help is appreciated.

Does any of your Pella casement 1 piece Bottom Hinge fit my Pella wood casement window vintage 1978, Bottom 2 piece Hinge with White Plastic Pivot Hinge with rollers? Also how do I order the white plastic pivot hinge pcs for left or right opening windows? These parts are left or right specific. I ... (cont.)

This is a removed lower hinge from a Pella window. The house was built in the late 70's. Do you have this part? If not, it looks similar to the end of any hinge arm assembly (see 39-394 for example) which I can saw off and modify to fit IF the rollers and hinge shoes are the same? ... (cont.)

Hello from Oklahoma, Need to verify if the TOP ARM shown in your picture goes on the top of the window?? In other words the shoe with the rubber rollers go on TOP?? My instinct thought the rollers would take the weight load of the window and would be on the bottom. Thanks for your help. ... (cont.)

I am in need of an older version of the Pella Pivot Plate Hinge Shoe From about 1980 time frame. The part I found on your site,39-363, looks very similar but mine had 2 circular bump outs that marry up with the holes in the part attached to the window See the attached photos 1468 & 9 ... (cont.)

Do u have to take out window to replace hinge mechanism?

I need all hardware to fix theses windows.please help identify. thanks, Todd

I purchased a few of your hinge arm assemblies for Pella awning windows. The ones that I received are to short and I wanted to see if you might be able to tell me if you have the correct ones? The ones that I purchased are item numbers 39-352 & 351. The length of the long arm of the one that I have ... (cont.)

Am looking for a pella hinged arm for a casement window and looking online find it but not the same as I have need some help

I recently purchased and installed the 39-096 Pella replacemnt crank from you. The attached images refer to a small plastic/nylon slider that is supposed to align the window itself in the frame when one opens and closes t6he crank. Although not associated with the crank itself, this part appears bro ... (cont.)