Viewing all customer Discussions for:

S385-30 30" Series 385 Channel Balance

Need to replace at least two windows - non-tilt channel balance. 30 inches long x .1/2 (5/8) x 9/16Thanks for your help

Hi I try to get (30" Window Channel 1/2) Balance but I don't sure about it, I add the images for help. I don't see the "2924DSL" series number in the list when I pick the 385 series. Please, I need be sure before purchase the product. thanks

There is no stamps on the channel balance. They appear to 1/2 inch wide and 30 inch in length. Four windows (8 balances) that measures approximately 50x32. Markings printed on the channel balances differ from window to window.

I'm looking for a replacement channel balance for my single-hung window. What is the equivalent Swisco part(s)? --ID stamp: BSI 29C --Window sash weight: 19 lbs. --Channel width: 1/2 inch --Channel depth: 10/16 --Channel length (metal only, less end caps): 30 in. Not sure about the plastic end piece ... (cont.)

I am looking for a part number for both sides of my window and the springs that go onside? The window is 51 inches wide and 61 inches in height, the metal bar that (the spring goes into I think they both fell out together) is 30 inches and the spring is 16 inches the only label inside the frame is t ... (cont.)

Need new balance

The original balances (from 8 years ago) were 2950 and too strong to lower the window easily. I had a contractor change 5 windows & he used 2940 & they work great. I have 10 more windows to change out...I attached pictures that show the 2940 and 2950 side by side. The plastic parts are simil ... (cont.)

Both window balances are broken They are stamped "IMP 29 DS 38 BS1 BT " The IMP DS and BT arestamped vertically in smaller type. The metal portion is 30" long. Window is about 30# or more and swings in from the bottom when lifted without the balances.What model do I order?James

I cant seem to find the correct top sash guide from your list. Measurements included in my photos. I recently purchase/installed 1 set of balances ( 30" SERIES 385 CHANNEL BALANCE fit perfect, thanks) and am ordering the remaining 9 sets + some replacement sash guides.

Not counting the connectors, the metal body is 30 inchese

I need replacement load balancers. The stamp is 29C USB.

Looking to replace all of mine. Need to identify so I can order If you need any further information please let me know.

This is the original Chanel balance. Can You match this with a product number in your stock?

I need to replace the pgt spring balancers. Balancer is 30" in length. 9/16" wide

Per the label on the window these are ALC-1 Alcan windows. Both channels do not stay in place. They tend to drop down. The one channel has a broken string. I'd like to get two new channels. The code on the channels is 2920-0. The channels measure exactly 31 inches including the plastic clips on each ... (cont.)

2930 B.S.I. BALANCE IS 30 INCHES NOT COUNTING THE PLASTIC CLIPS

I need 8 pairs of these balance. The part number is showing in the picture. They show different numbers, but they all actually look the same to me. The two plastic ends look the same. Can you help me to identify which part I need to buy? Thanks a lot!

Window brand. Norandex. Clips have broken on all windows allowing balancers to pop up on side track of windows. I am not referring to clips attached to balancers. Do I need to replace balancers that appear to be fine and just reinstall with new clips as shown in photo?

You can see the front and back of each end of the plastic clips. The number etched into the track is 2910. Measuring it metal track end to metal track end it is 30" I have some tracks in my checkout cart already....I THINK I have the correct ones but I'd rather you tell me which track I should order ... (cont.)

I was hesitant to order 4 of Product Code: S385-30 on-line because the bottom fitting seems to be a little different. I don't think it will make much difference but wanted to check and make sure.ThanksRick