Viewing all customer Discussions for:

26-040 Pivot Bar, 3"

Can you help me identify the proper balance and shoe and pivot bar please?Thank you,Mark

It is 29 inches long with a white plastic covering. This came off a bedroom window and needs replacement. I also will need the adjustment tool. The diameter of the spiral balance is 3/8 inches

Hi! Today, I opened my windows to lubricate the balancers. I pulled them inward to find that the tilt pivot bars were so rusted that they actually broke. The tilt pivot bars snapped from the balance shoes. We were able to remove the rusted pivot bars. I'm not yet sure how to remove the balance shoes ... (cont.)

Spiral balance works fine, just these pivot bar housings have gone bad. If you can also identify the pivot bars that would be great, since they started to bend.

Pictures attached: need balances...they are not attached to the sides of the windowthey move with the window. Also, need the white plastic pieces that stop top sash from going to far down, as well as the pieces for the bottom sash to prevent it from going all the way to the top. Quantity of 10. ... (cont.)

Part of the window where Pivot Bar gets screwed in to. Pivot bar in a bathroom window is rusted in to this window part. Do you carry this plastic part? Length 3 and 1/8" Width 6/8" see pictures attached.

Hello you were very helpful in identifying and ordering replacement tilt bars. However, now I'm unable to remove the corroded remaining pieces. My window installer tells me that a tilt bar holder assembly needs to be replaced. Are you able to help point me in a general direction.Thank youScott ... (cont.)

Hello I am having trouble locating the correct pivot bar for my window sash.

Cannot find replacements, and should probably order plastic pivot holders(photo).

I need spiral balance for 4tilt windows 37" black tipAlso pivot Shoe for 4windows 15-047?3" pivot bars 26-040?Top tilt latch for 4windows 1"x3" 2" center 26-344And a tool 75-033 I don't know if I chose the right parts parts the latches have to be brown or black . What say you?The balance number is S ... (cont.)

Hello, Thanks for your assistance in locating this replacement part. The window will not stay up. I have determined that the window will not stay up because the window balance shoe is broken and cannot attach to the window. The shoe is also missing the blue bushing. Probably because it's broken a ... (cont.)

i am needing 3 sets of the pivot pins and 3 sets of ballasts. The pics of the note paper has the sash dimensions.

Dear Swisco,Enclosed please find photo's taken of my existing single hung tilt window.I would like to replace 2 spiral tilt window balances, 2 pivot shoes, 2 pivot bars and need a charging tool.My existing window is approx. 23 years old and the frame is aluminum. I do not know the manufacturer.1.The ... (cont.)

The bars are 3" long, 5/16" wide and 3/16" tall. They have two holes. The protrusion line (one on each end so they appear to be reversible) is 3/8" from the end. The holes are approximately 1" from each other. The first hole (either end) is 1" from the very outside edge. The manufacturer of the ... (cont.)

This is a pivot bar from an Air Master DH, manufactured in 1988. It is 1/4" wide and "U" shaped and must fit into a pivot shoe. Would you have a match for this? I need 6 pieces. Thank you.

Hi there! I need to replace the ~3 inch long metal strip that is embedded in the bottom rail of the window, and rests inside the channel balance shoe - it's the piece that pivots the shoe as the window folds out. Do you carry these for a Pennco single-hung? Uploaded a picture of the metal piece (l ... (cont.)

Can you tell me what parts I need from your site please

Need several have 100+ windows

On some of my window the pivot bar is rusted and broke off do you have these

Hi, I need help with a window. To start, I've attached pictures. I'm sure you'll have other questions to help me purchase the correct pieces. Please contact me by email Thank you, Debbie