Viewing all customer Discussions for:

S395-30 30" Series 395 Channel Balance

Hello,I need help determining which balances would work for these windows. The glass etching says they are Herculite. The balance numbers are different than what I am used to seeing so I'm hoping you will know what will work. Here are all the numbered balances;1) Entry. 21 2 Bsi oe ... (cont.)

I had a problem with one of the windows. Managed to fix it, but would like to get some replacement balances because the problem will probably happen again. The numbers on the balance are ' 29 3 PQ CALDWELL '. I should have measured the length when I had it out, but forgot to do that. ... (cont.)

Kinco made window, need channel balances for two windows. One is marked "29-6 KX CMC 7". The other has no marking on t, and is 35 inches long. End hardware is the same for both sets of channel balances.

Looking for balances and upper sash clips for pgt windows non tilt windows bottom sash only opens. Wt of sash is 30 lbs. Glass is roughly 48 inches wide. Thank you, John Powers

29 3 AP Caldwell Need replacement part for the above

Which model do I need? Thanks

Ref telecom today, photos of balance need replacement.Chris

Hi I need help identifying my bottom window channel balance. Hard to read but the info on the back looks like: 29 1 FO CALDWELL I measured 30", excluding the plastic attachments. Photos of both ends of the plastic attached. Thank you!

I need to replace 6 channel balances on my PGT windows. The replacement part must include the top, shoe, spring and cord as shown in the photos. The PGT part number for each channel balance is as follows: 23-9 HV Qty=2 29-4 JV Qty=4

35-4-ix-cmc-7 28-5-kx-cmc-11 28-4-kx-cmc-7 29-4-lx-cmc-7 Thanks for the help.

The length of the balance is 30". The depth of the shoe is 1 1/8". The stamped markings are 29 4 BS1. Thank you.

My bank vet has a stamping of 29-9 cmc 11. It appears to be a 390 series. Which 2 would I order? It is for a pgt non tilt window.

4 digits- 2965(B61 sideways) RV . Its measure 30 inch in length and 9/16 in width.The whole thing is broken. Trying to find the best replacement part

I need two replacement window channel balances for my Viking window. They are 1/2" wide and have the number 2930 on them. I couldn't find them in your parts section. Do you stock these? Thanks, Scot

HiCan you please tell me which series to purchase?In the picture with 4 channels-they are 2630 and 27 inches long.In the picture with one channel, it is a 2930 and 30 inches long. This one seemedTo come out of a window with another 2630 might b the reason the window was broken. I have 13 windows to ... (cont.)

Need help identifying the correct channel balance and top end pieces to purchase for a PGT single hung window. the balance is 30" long and 5 1/6 wide. I have a couple of pictures attached.

I need window's CHANAL balance W1/2" L31" for E.S.P. WINDOW See piocture please.

The number is 29307 and the aluminum part measure 30". What type of replacement do I need? Thank You.

My channel balance are 30inches long 1/2" wide, and the markings on them are 29 3 IP Caldwell. The first number may be 28, its hard to be sure. I have submitted three pictures with this email. Would you please give me a quote on these. Thank You, Tom

Balance reads " 29 9 BT caldwell. also right upper clip may be broken (image 1069) Springs are rusty and cable is broken. I've seen video and I'm confident I can replace them.