Viewing all customer Discussions for:

S395-30 30" Series 395 Channel Balance

Can you help me identify the correct part to purchase from you. I believe these would be a S395-30 in 2910 weight rating

The existing channel balance does not have a number stamped on it. Print info say " 29 3 HR CALDWELL" ? Does this relate to a specific replacement part. Sash weight around 32 lbs. Also have smaller Kinco window with 18" lower sash, with around 16" channel balance. Do you have that replacement pa ... (cont.)

AS can be seen on the photo, there is a marking, "29 5 DW CMC 4". After searching your website, it appears that the S385-30-2950 might work. What do you think?

Hello. We are trying to find balance rod replacements for several of our windows. The one in the photo is stamped with 2919, we need about 20 of these including the plastic sash cams. Do you have parts available? Some of the others we need are stamped with 3428. I believe we need 10 of these along ... (cont.)

30" length 5/8 wide

I hope you can help me identify these caldwell balancers. I need two of them to fix a PGT window. The length without the ends is 30".

Hi I need 2 new channel Balances for my PGT window.. I have attached pictures with the # 29 5 GV CMC 1 stamped on it Could you advise me on the correct one to order Thank you Keith

Hi, I need 2 window balancers replaced. The window is a PGT single hung window SH - 4000. Model number is 6SHSTKR. The balance is stamped 29-4 LX CMC 7. The window size is 80 by 87 cm. I attached the pictures of the balancers. The length of the metal part of the balance is 76 cm (depth and width 1.5 ... (cont.)

Just placed an order for new Top Sash Guides for PGT windows. Thinking I may also need a new channel balance for at least one window. Can you confirm my guestimation? Length of the metal channel is just shy of 30 inches (29 15/16). Top attached looks like 19-005. Bottom shoe looks to be 15-001. This ... (cont.)

Please help identifying these parts for 20 yr. old PGT windows. See attached images. - Channel balance is stamped BSI 2940ff. 30

I removed this channel balance from a window, bottom rusted and gone where plastic foot holds pulley wheel. I watched your Utube video and think you may be the people to provide me the replacement part. The stamping on the steel says 29 3 LT CMC 3. The picture may show this as well. Thanks ... (cont.)

Need help identifying which replacement balance I need. My broken balance is 30" long and has the part number 29 4 BW CMC 7.

Looking to replace sash balances from older single hung, non tilt, viking 9300 windows 3-10 by 5-10. Length of balance metal housing is 30". Is your S385-30-2950 a good replacement?

Hello, Can you please tell me, based on the attached pictures, what channel guides I need to purchase to repair my windows. On my window channels they say the word Caldwell with this: 29 3 DQ and they are 31 inches, end to end.

I need help identifying what parts I need to help me fix the window. It will open fine, but won't stay open. You can see in the picture that the metal rod on the side is sliding down. Any help you can provide is much appreciated. aama h-lc30-53x78

I need to replace 6-8 Channel Balances for my Atrium Windows. I think the Atrium part # is 5W12Balance. They are 1/2 inches in width and 30 inches long and stamped with the #2940 on them.

Need help identifying balances for PGT window where window is about 47" wide x 61" high. Stamped on balance is 29 5 IW CMC 11 as shown in one of the four attached pictures. Metal part of balance is 30" long x 0.5 inches wide. Need to know what balance to order that has proper ends as shown in attach ... (cont.)

MY BALANCER TUBE IS 31.25 INCHES AND HAS 29 5 AX CMC7 PRINTED ON IT.

First, thanks again for your help on my previous order. I need channel balances, take out clips and sash guides for a no-tilt window. Channel balances are 30" x 5/8" x 5/8", with a stamp showing 29DS 38 (see pic). Please help me ID the parts. Thank you.

Channel balance. Was a block and tackle but that came a part. Stamped on side 29 2 JP Caldwell