Viewing all customer Discussions for:

26-040 Pivot Bar, 3"

I'm trying to replace all the parts on my old double hung windows. One problem is the pivot bars are so rusted that the screw heads are sheared off. Any thoughts on removing them?

Hi, I'm trying to select the correct size sash carrier and coil balance for a double hung replacement vinyl window that is about 15 years old. The window panels are 36" x 18". Only the lower carrier and coil need to be replaced on both sides. Markings on the existing sash carrier are 8L and 8R. The ... (cont.)

Picture of constant force balance, pivot bar, and plastic housing for Pivot bar. The pivot bar rusted away, and the constant force housing I would also like to replace. The housing had the #4 marked in middle, but rubbed off when I cleaned it. I believe what I need is your Coil housing pivot (15-087 ... (cont.)

Metal post that helps window sit without sliding down. What is it called? Ours snapped and broke.

Window was bought at Home Depot.

The pivot bar is 5/16 wide and 3/16 tall. Not sure which one to order.

If someone could help me find these window parts would be greatly appreciated thanks so much Paul

I am looking for a part to connect a window to the pully system of the frame. It looks like there may be a square peg that does this. Please see picture of bottom of window with square hole and photo of the piece of the pulley system on the frame where these is a square hole. I can't find any number ... (cont.)

Hello I have a vinyl builders window with a hardware measurement of 27" in regards to the above photos. I'm also looking for the bottom hardware post that inserts into the bottom balance as it snapped off in the above photo also. Thanks for your help, Warren

I'm not sure what size shoes I need and I can't find pivot bars that fit the same shoes already installed. Part of the origins bar has snapped off and is stuck inside the shoe in the picture. Please advise on how to move forward to fix this issue please.

I am searching for replacement pivot pins for my windows. The photo is the intact pin. The other side totally rusted out and crumbled. Do you happen to carry these?

Pivot pin 2 7/8 " with a hole for screw 1" in. The end is not smaller. I squeezed it with pliers to get it out. Thank you, Adam

I have received the parts ordered but the 15-118 pivot shoe is not the right one. Although it is close. The window insert that I have is a female. Please advise.

The pivot at the bottom of my widows is totally rusted out. The window comes right out of the window frame. Can they be replaced? What is the part number? I will also need to replace the shoes and balances. The house was built in 1999. Thank you

Hello, I need two parts for my window. The bar has 985 2-A. It's 2.5 inches long. The pivot lock shoe has a 7 on it. That is also 2.5 inches in length and about 1 inch wide. It's hard to measure without taking it out. Thank you

I was able to find on your website the two Spiral Balances I need (S400-31), the two metal brackets #62 (17-062) and the Spiral Balance Charging Tool for Non-tilt Windows (75-005). I need to order these parts as soon as possible, but I have four small plastic parts that hopefully you can help me fi ... (cont.)

Hello, This metal piece broke loose from the bottom of my window pane/sash. Can you help me determine what I need to repair this window? Thank you!

I have BF Rich Windows 013460 4098 DH VTCL LE 1 VTL240EW.I need Coil Balance Shoe W 1 1/4"x H 1 3/8" x 9/16" and Balance Spring (2 sets) for W 28.625 H 61.5 C 30.75 15 LBS(1 set) for W 28.625 H 37.25 c 18.62 10LBS Thank YouDale

Looking for replacement parts

We need to sash pivots please thank you